Abstract:Laser-induced breakdown spectroscopy (LIBS) is an elemental analysis technique widely used throughout science and engineering. A limitation of LIBS is the low analytical sensitivity for trace elements. Therefore, it is of great significance to enhance the signal intensity and reduce the detection limit of LIBS. To enhance LIBS signals, here we propose a method, multiple discharges-enhanced LIBS. The measurements were performed on a solid aluminum alloy. A nanosecond laser was focused on the alloy to generate plasma. The plasma was sputtered into the air between the two discharge electrodes, which triggered the discharge. Multiple discharges were generated by using a high-frequency discharge power source. The multiple discharges excite, heat the plasma and extend the plasma duration, thereby enhancing the signal intensity. Here, a direct current pulse power source with a frequency of 100 kHz was used, and five discharges occurred after each laser-induced breakdown. We show that compared with LIBS, the plasma duration is extended by approximately 50 tes. Multiple discharges-enhanced LIBS increases the signal intensity of Mg II (at similar to 279 nm) by about 48 times; Al II (at similar to 358 nm), 72 times; trace element Mn I (at similar to 403 nm), 6. 3 times; trace element Cu I (at similar to 403 nm) , 8. 3 times. The detection limit of Mn I (at similar to 403 nm) is reduced by a factor of 6; Cu, 8. Multiple discharges-enhanced LIBS dramatically enhances the signal intensity and improves the detection limit of LIBS, and it expands the applications of LIBS. This method has the potential to be applied to the identifications of valuables, rare materials and cultural relics.

Femtosecond laser-ablation spark-induced breakdown spectroscopy and its application to the elemental analysis of aluminum alloys

Application of quantitative analysis for aluminum alloy in femtosecond laser-ablation spark-induced breakdown spectroscopy using one-point and multi-line calibration

Quantitative Analysis of Elemental Concentrations of Aluminum Alloys Using Calibration-Free Femtosecond Laser-Ablation Spark-Induced Breakdown Spectroscopy

Laser Ignition Assisted Spark-Induced Breakdown Spectroscopy for Element Analysis of Aluminum Alloy with Enhanced Sensitivity

Application of Fiber Optic High Repetition Rate Laser-Ablation Spark-Induced Breakdown Spectroscopy on the Elemental Analysis of Aluminum Alloys

Calibration-free Elemental Analysis Combined with High Repetition Rate Laser-Ablation Spark-Induced Breakdown Spectroscopy

One-Point and Multiline Calibration Fiber-Optic Laser-Ablation Spark-Induced Breakdown Spectroscopy for Quantitative Analysis of Elements in Aluminum Alloys

Sensitive Elemental Analysis with High Repetition Rate Laser-Ablation Spark-Induced Breakdown Spectroscopy Combined with Lock-in Signal Detection

Elemental Analysis of Copper Alloy by High Repetition Rate LA-SIBS Using Compact Fiber Spectrometer

Quantitative Elemental Analysis Of Aluminum Alloys With One-Point Calibration High Repetition Rate Laser-Ablation Spark-Induced Breakdown Spectroscopy

Determination of Copper, Magnesium, and Manganese in Aluminum Alloys Using Laser-Induced Breakdown Spectroscopy Based on Fiber Laser Ablation

Time-Resolved Laser-Induced Breakdown Spectroscopy of Aluminum

Laser-ablation Dependence of Fiber-Laser-based Laser-Induced Breakdown Spectroscopy for Determining Cu, Mg, and Mn Elements in Aluminum Alloys

Quantitative aluminum alloys analysis using laser-induced breakdown spectroscopy

Triggered Parallel Discharge in Laser-Ablation Spark-Induced Breakdown Spectroscopy and Studies on Its Analytical Performance for Aluminum and Brass Samples

Spectral Filtering Method for Improvement of Detection Accuracy of Mg, Cu, Mn and Cr Elements in Aluminum Alloys Using Femtosecond LIBS.

Application of Calibration-Free High Repetition Rate Laser-Ablation Spark-Induced Breakdown Spectroscopy for the Quantitative Elemental Analysis of a Silver Alloy.

Using Laser-Induced Breakdown Spectroscopy on Vacuum Alloys-Production Process for Elements Concentration Analysis

[Elemental Analysis of Alloys with Picosecond Dual-Pulse LA-LIBS under Low Sample Destruction].

Elemental Analysis of Copper Alloys with Laser-Ablation Spark-Induced Breakdown Spectroscopy Based on a Fiber Laser Operated at 30 Khz Pulse Repetition Rate

Multiple Discharges-Enhanced Laser-Induced Breakdown Spectroscopy