Abstract:Marine and coastal infrastructures usually suffer from synergetic effect of corrosion and wear known as tribocorrosion, which imposes strict requirements on the structural materials used. To overcome this problem, novel composite wear- and corrosion-resistant xTiC-Fe-CrTiNiAl coatings with different TiC content were successfully developed. The coatings were obtained by the original technology of electrospark deposition in a vacuum using xTiC-Cr2Ti-NiAl (x = 0, 25, 50, 75%) electrodes. The structure and morphology of the coatings were studied in detail by XRD, SEM, and TEM. The effect of TiC content on the tribocorrosion behavior of the coatings was estimated using tribological and electrochemical (under stationary and wear conditions) experiments, as well as impact testing, in artificial seawater. The TiC-free Fe-Cr2Ti-NiAl coating revealed a defective inhomogeneous structure with transverse and longitudinal cracks. Introduction of TiC allowed us to obtain coatings with a dense structure without visible defects and with uniformly distributed carbide grains. The TiC-containing coatings were characterized by a hardness and elastic modulus of up to 10.3 and 158 GPa, respectively. Formation of a composite structure with a heavily alloyed corrosion-resistant matrix based on α-(Fe,Cr) solid solution and uniformly distributed TiC grains led to a significant increase in resistance to stationary corrosion and tribocorrosion in artificial seawater. The best 75TiC-Fe-CrTiNiAl coating demonstrated the lowest corrosion current density values both under stationary (0.03 μA/cm2) and friction conditions (0.8 μA/cm2), and was characterized by both a 2-2.5 times lower wear rate (4 × 10−6 mm3/Nm) compared to AISI 420S steel and 25TiC-Fe-CrTiNiAl and a high fracture toughness.

Tribocorrosion Behavior in Artificial Seawater and Anti-Microbiologically Influenced Corrosion Properties of TiSiN-Cu Coating on F690 Steel

Structural, Mechanical and Tribocorrosion Behaviour in Artificial Seawater of CrN/AlN Nano-Multilayer Coatings on F690 Steel Substrates

Tribocorrosion behaviour of F690 and 316L steel in artificial seawater

Structure and tribocorrosion behavior of CrMoSiCN nanocomposite coating with low C content in artificial seawater

Influence of Carbon Contents on the Structure and Tribocorrosion Properties of Tisicn Coatings on Ti6al4v

Influence of Bias Voltage on Structure and Tribocorrosion Properties of TiSiCN Coating in Artificial Seawater

Tribocorrosion characteristics of CrMoSiCN/Ag coatings on Ti6Al4V alloys in seawater

Long-term tribocorrosion resistance and failure tolerable of multilayer carbon-based coatings

Comparative Investigation on the Tribocorrosion Resistance of Ti6Al4V and 60NiTi Alloys in Simulated Seawater Environment

Comparative Investigation on the Tribocorrosion Resistance of Ti6Al4V and 60niti Alloys Inimulated Seawater Environment

Study on Friction and Corrosion Performance of CrTiBN Coating in Artificial Seawater Environment

Surface tribological and electrochemical properties of TiAlSiN coating in seawater

Tribocorrosion evaluation of AISI 431 coated with tungsten oxynitride

Influence of TiC Addition on Corrosion and Tribocorrosion Resistance of Cr2Ti-NiAl Electrospark Coatings

Microstructure and Tribocorrosion Properties of Ni-Based Composite Coatings in Artificial Seawater

Tribological behaviors of TiSiC coating in seawater environment

Effect of CrYN/TiBN coating on friction performance and corrosion resistance of 316 Stainless Steel in artificial seawater

(Digital Presentation) Anti-Corrosion Investigation of Titanium Electrode for Cu Plating

Corrosion and Tribocorrosion Behaviors of AISI 316 Stainless Steel and Ti6Al4V Alloys in Artificial Seawater

Tribological study of Ti3SiC2/Cu5Si/TiC reinforced Co-based coatings on SUS304 steel by laser cladding

Effect of bias voltage on the tribocorrosion performance of TiAlSiN coatings on FH790 steel by arc ion plating