Abstract:In this article, a class of <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$2^{n}$ </tex-math></inline-formula> -way wideband filtering power dividers (FPDs) is presented and designed with a wide isolation band. It consists of ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$2^{n}-1$ </tex-math></inline-formula> ) two-way power-dividing units and <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$n$ </tex-math></inline-formula> three-line coupled lines. The basic two-way power divider is achieved by replacing a simple isolation resistor of the conventional Wilkinson power divider with a modified isolation network, so as to improve the bandwidth of better-than-20-dB isolation band from 40% to 120%. The modified isolation network is composed of one quarter-wavelength coupled line, two quarter-wavelength transmission lines, and one resistor. The three-line coupled line is introduced at each output of the proposed FPD to improve its frequency selectivity and passband bandwidth. Furthermore, after placing one additional isolation resistor on each three-line coupled line, the number of output ports in the proposed power divider could be doubled without introducing more two-way power-dividing units. Finally, a prototype two-way and two prototype four-way wideband FPDs with different occupied sizes are designed and fabricated. The feasibility of the proposed design method is verified by the good agreement between the simulated and measured results.

Filtering Power Divider with Wide Stopband Using Open-Stub Loaded Coupled-Line and Hybrid Microstrip T-Stub/DGS Cell

Design of a Wideband Filtering Power Divider with Good In‐band and Out‐of‐band Isolations

Design of Compact Wideband Filtering Power Divider with Extended Isolation and Rejection Bandwidth

Design of Wideband Filtering Power Dividers with Harmonic Suppression Based on the Parallel-Coupled Line Structures

Wideband Filtering Power Divider with Deep and Wide Stopband

A 3.4–7.4-Ghz Filtering Power Divider with Wide Stopband and Low Radiation Loss Using Triple-Mode Hybrid Microstrip/SIDGS Resonator

Design of Filtering Power Divider with High Frequency Selectivity

Dual-Band Filtering Power Divider Using Dual-Resonance Resonators with Ultrawide Stopband and Good Isolation

Compact 4.0–5.1 GHz Filtering Power Divider with Low Insertion Loss and Wide Stopband Using RC-Loaded Coupled SIDGS Resonators

Double‐layer Microstrip Ultra‐wideband Filtering Power Divider with High Selectivity and Large Isolation

Quasi-elliptic Bandpass Filtering Power Divider with Ultra-Wide Stopband

Wideband Four-Way Filtering Power Divider with Isolation Performance Using Three Parallel-Coupled Lines

High-performance filtering power divider with multiple transmission zeros

Reconfigurable Dual-Band Filtering Power Divider with Ultra-Wide Stopband Using Hybrid Microstrip/Square Defected Ground Structure

Wideband filtering power divider based on D-CRLH resonator

A Novel Wideband Filtering Power Divider With Embedding Three-Line Coupled Structures.

Dual-Band Bandpass Filter and Filtering Power Divider with Ultra-Wide Upper Stopband Using Hybrid Microstrip/DGS Dual-Resonance Cells

A Miniaturized Filtering Power Divider With High Selectivity and Wide Stopband Based on 3D Heterogeneous Integration Technology

Millimeter Wave Dual Wideband Filtering Power Divider Using Groove Gap Waveguide and Spoof Surface Plasmon Polariton

Filtering Power Divider with Ultrawide Stopband and Wideband Low Radiation Loss Using Substrate Integrated Defected Ground Structure

2<italic><sup>n</sup></italic>-Way Wideband Filtering Power Dividers With Good Isolation Enhanced by a Modified Isolation Network