Abstract:Journal of Thermoplastic Composite Materials, Ahead of Print. In this study, bio-composites were developed using polylactic acid (PLA) as the matrix and sisal fibers (SFs) derived from agave sisalana leaves as the reinforcement. The bio-composites were prepared through injection molding with the addition of tributyl 2-acetylcitrate (ATBC) plasticizer. The mechanical, thermal, and rheological properties of these bio-composites were investigated to understand the effects of fiber and plasticizer contents. The results showed that the addition of SFs improved the tensile and flexural moduli of the bio-composites but led to a decrease in tensile strength compared to neat PLA. The flexural strength initially decreased with low fiber content but recovered to the level of neat PLA as the fiber content increased. The impact strength increased with the incorporation of SFs and ATBC. However, the presence of ATBC had a negative impact on the tensile and flexural properties of the bio-composites. The thermal conductivity of the materials was influenced by the fiber content and processing temperature, increasing with SFs inclusion but decreasing with temperature. Differential scanning calorimetry analysis revealed increased crystallinity of PLA with the presence of SFs and ATBC. The specific heat capacity increased with ATBC but decreased with increasing SFs. Dynamic mechanical property testing showed variations in storage and loss moduli of the bio-composites at different temperatures. The storage modulus increased with higher fiber content and abruptly dropped around glass transition temperature. Rheological characterization demonstrated effective interactions between the fibers and matrix with good fiber dispersion, resulting in uniform shear viscosity versus shear rate for different capillary dimensions. The shear viscosity of the SFs/PLA mixture increased with increasing fiber content but decreased with the addition of plasticizer. Furthermore, the compounding and molding processes had a notable impact on the microstructure of the fibers, specifically resulting in fiber breakage and fiber separation during processing.

Preparation and Characterization of Poly(lactic Acid)/sisal Fiber Bio-Composites under Continuous Elongation Flow

Crystallization behavior and mechanical properties of bio-based green composites based on poly(L-lactide) and kenaf fiber

Effects of Bamboo Cellulose Nanowhisker Content on the Morphology, Crystallization, Mechanical, and Thermal Properties of PLA Matrix Biocomposites

Preparation of Long Sisal Fiber-Reinforced Polylactic Acid Biocomposites with Highly Improved Mechanical Performance

A study of the mechanical, thermal and rheological properties of sisal fiber-reinforced polylactic acid bio-composites with tributyl 2-acetylcitrate as a plasticizer

Simultaneous Enhancement of Strength and Toughness of PLA Induced by Miscibility Variation with PVA.

Effect of Initial Fiber Length on the Rheological Properties of Sisal Fiber/Polylactic Acid Composites

Interface Bond Improvement of Sisal Fibre Reinforced Polylactide Composites with Added Epoxy Oligomer.

Structural Properties and Mechanical Behavior of Injection Molded Composites of Polypropylene and Sisal Fiber

Characterization of poly(butylene succinate)/poly(lactic acid) blends with in-situ sub-micron fibers and intercalation structure manufacturing by volumetric pulsating elongation flow

Preparation of super-toughened Poly(L-lactide) composites under elongational flow: A strategy for balancing stiffness and ductility

Strong Shear Flow-Driven Simultaneous Formation of Classic Shish-Kebab, Hybrid Shish-Kebab, and Transcrystallinity in Poly(Lactic Acid)/Natural Fiber Biocomposites

Preparation and Properties of Straw Fiber/Polylactic Acid Composites

Study on the Compatible Interface of Bamboo Fiber/polylactic Acid Composites by In-Situ Solid Phase Grafting

Effects of PLA-Type and Reinforcement Content on the Mechanical Behavior of Additively Manufactured Continuous Ramie Fiber-Filled Biocomposites

Reinforcement of Polypropylene Using Sisal Fibers Grafted with Poly(methyl Methacrylate)

Preparation and Characterization of Polylactic Acid-G-bamboo Fiber Based on In-Situ Solid Phase Polymerization

Properties and Morphology of Poly(Lactic Acid)/Calcium Carbonate Whiskers Composites Prepared by a Vane Mixer Based on an Extensional Flow Field

Poly(l-lactide)/poly(d-lactide)/bamboo fiber (BF) bio-composites with enhanced heat resistance, mechanical and rheological performance

Toward durable polylactic acid/poly(methyl methacrylate) polyblend fibers with high performance

Pultrusion of flax/poly(lactic acid) commingled yarns and nonwoven fabrics