Abstract:Supplemental damping devices, including passive, semiactive, and active systems, can be employed to reduce vibrations caused by various hazards. This paper examined tuned liquid column dampers (TLCDs), a specialized type of tuned mass damper typically used to reduce the response of the structure around a specific frequency. A variation of the tuned liquid damper previously studied by the authors is a tuned liquid wall damper (TLWD), in which multiple liquid columns are embedded within a RC shear wall. The TLWD eliminates the space requirement of a conventional tuned liquid damper by distributing the liquid mass vertically into multiple columns throughout the structural shear wall system, and enables reaching a higher frequency range through the design of the TLWD geometries. This study investigated the optimal design of TLWD systems to mitigate multiple hazards, in particular nonsimultaneous wind and seismic hazards, based on a life-cycle cost (LCC) objective function. This was done using a probabilistic life-cycle analysis procedure that leveraged Bayesian optimization (BO) to search for the most promising permutation of tuning parameters that minimize the LCC under the design loads, with Monte Carlo simulations used to propagate the record-to-record variability of wind and seismic hazards. The proposed procedure was demonstrated on a 20- and a 42-story building subjected to nonsimultaneous wind and seismic excitations. The vertically distributed TLWDs were subjected to geometric constraints provided by the wall systems, and tuned to multiple frequencies enabling multimode mitigation. Afterward, the optimal tuning parameters were identified using the LCC-BO algorithm. Results showed that the multimode TLWD tuned with optimal tuning parameters effectively mitigated both wind and seismic hazards, leading to 32.8% and 43% total LCC reduction for the 20- and 42-story buildings, respectively, compared with the buildings without dampers, excluding the cost of the mitigation system. A performance comparison with a traditional tuned liquid column damper (TLCD) installed at the top of the buildings demonstrated that the multimode TLWD system outperformed the TLCD with an approximate 9% reduction in LCC for both the 20- and 42-story buildings.

Practical Displacement-Based Seismic Design Approach for PWF Structures with Supplemental Yielding Dissipators

Dissipation in Sheathing-to-framing Connections of Light-Frame Timber Shear Walls under Seismic Loads

Static and dynamic inelastic P -Δ effect for seismic design

Performance-Based Seismic Design and Evaluation of Fused Steel Diagrid Frame

Linear‐elastic Lateral Load Analysis and Seismic Design of Pin‐supported Wall‐frame Structures with Yielding Dampers

Performance-based seismic design method for disc spring-based self-centering viscous dissipative braced steel frame

Seismic performance design of energy-dissipated structure system based on damage control and time-varying damping ratio

Subassemblage Tests on Seismic Behavior of Double-Corrugated-plate Shear Walls

Displacement-based Design Method for Energy Dissipation Structures with Nonlinear Viscous Dampers

Study on Displacement-Based Design Method for Energy Dissipation Structures

Seismic Design Based on the Yield Displacement

Experimental investigation of steel-reinforced precast shear wall with replaceable energy dissipators

Optimal Seismic Design for Self-Centering Concrete Wall Structures Equipped with U-shaped Flexural Plate Dissipaters

Numerical Study on Hysteretic Behaviour of Horizontal-Connection and Energy-Dissipation Structures Developed for Prefabricated Shear Walls

Seismic control of super high‐rise structures with double‐layer tuned particle damper

Risk-Informed Design Optimization of Vertically Distributed Tuned Liquid Wall Dampers for Multihazard Mitigation

Energy-Balance-Based Plastic Design and Seismic Fragility Analysis of Steel Plate Shear Wall Coupled with Steel Side Columns

Seismic performance of prefabricated wall panels with sliding joints for reinforced concrete frames

A direct displacement-based seismic design method

Performance-based-plastic-design of damage-control steel MRFs equipped with self-centring energy dissipation bays

Performance-Based Seismic Design of Corrugated Steel Plate Shear Walls