Enhanced Hydrogen Production Performance Through Controllable Redox Exsolution Within CoFeAlOx Spinel Oxygen Carrier Materials

Dewang Zeng,Yu Qiu,Song Peng,Chao Chen,Jimin Zeng,Shuai Zhang,Rui Xiao

DOI: https://doi.org/10.1039/c8ta02477d

IF: 11.9

2018-01-01

Journal of Materials Chemistry A

Abstract:Chemical looping performance can be improved through the controllable exsolution of the redox phase in a spinel solution.

What problem does this paper attempt to address?

Cu–Fe–Al–O Mixed Spinel Oxides As Oxygen Carrier for Chemical Looping Hydrogen Generation

Dongxu Cui,Yu Qiu,Min Li,Li Ma,Shuai Zhang,Dewang Zeng,Rui Xiao

DOI: https://doi.org/10.1016/j.ijhydene.2020.02.145

IF: 7.2

2020-01-01

International Journal of Hydrogen Energy

Abstract:The reduction level for a metal oxides carrier determines the final hydrogen yield for a chemical looping hydrogen generation process. Nevertheless, when the oxygen carrier is reduced at a high level, the sintering of materials would be accelerated. In this paper, we prepare a Cu0.2Fe0.8(FeAl)O-x spinel material and investigate its hydrogen production performance. The results indicate that it exhibits a good redox stability even at reduction level of 0.75 during 20 cycles. In contrast, the deactivation of Fe2O3 oxygen carrier can be obviously observed in the first few cycles. This enable the material with stable hydrogen production at a high yield about 7 mmol/g, which is 3.5 times higher than that of Fe2O3. Upon SEM and XRD characterization techniques, we find that the reason of the both good stability and high hydrogen yield is that the ability of spinel support to inhibit sintering of Cu and Fe active compositions. (C) 2020 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
A Mixed Spinel Oxygen Carrier with Both High Reduction Degree and Redox Stability for Chemical Looping H2 Production

Dewang Zeng,Dongxu Cui,Yulin Lu,Yu Qiu,Min Li,Shuai Zhang,Rui Xiao

DOI: https://doi.org/10.1016/j.ijhydene.2019.11.062

IF: 7.2

2019-01-01

International Journal of Hydrogen Energy

Abstract:Developing the oxygen carrier of high reduction degree and redox stability has key importance to the chemical looping hydrogen production. However, high reduction degree of oxygen carrier often leads to severe sintering and poor redox stability. Therefore, the trade-off between such two aspects of it must be considered. In this paper, a Co0.5Fe0.5(-FeAl)O-x material was reported as an oxygen carrier and an investigation on the performance of its chemical looping hydrogen production was conducted. It exhibited a stable and high hydrogen yield of 8.53 mmol/g during 20 cycles even at the reduction degree of 0.75. Upon comparison, it was found that the obvious deactivation occurred in Fe2O3 material when its reduction degree was higher than 0.25. Upon various characterization techniques, we found that the high performance of such material was rightly because of the reversible exsolution and dissolution of its active compositions from and into the parent spinel support. (C) 2019 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
Mn-Fe-Al-O Mixed Spinel Oxides As Oxygen Carrier for Chemical Looping Hydrogen Production with CO2 Capture

Dewang Zeng,Dongxu Cui,Yu Qiu,Min Li,Li Ma,Shuai Zhang,Rui Xiao

DOI: https://doi.org/10.1016/j.fuel.2020.117854

IF: 7.4

2020-01-01

Fuel

Abstract:Preparing the oxygen storage material capable of being highly reduced with desirable stability is important to reduce the solid circling rate in a fluidized bed chemical looping reactor. Nevertheless, the high oxygen carrier reduction degree would accelerate sintering. In this work a Mn0.5Fe0.5(FeAl)O-x material is synthesized as the oxygen carrier of chemical looping hydrogen production process. It exhibits a good redox stability during 30 cycles even operated at reduction degree of 0.8. In fixed bed tests, the Mn0.5Fe0.5(FeAl)O-x material shows a high and stable hydrogen yield of 2.1 mmol/g at 20th cycle, while the CO completely converts to CO2. In contrast, the deactivation can be obviously observed in the case of Fe2O3 oxygen carrier. The hydrogen yield is only 0.44 mmol/g at 20th cycle which is about one fifth of Mn0.5Fe0.5(FeAl)O-x sample.
Earth Abundant Spinel for Hydrogen Production in a Chemical Looping Scheme at 550 °C

Yu Qiu,Li Ma,Qingfeng Kong,Min Li,Dongxu Cui,Shuai Zhang,Dewang Zeng,Rui Xiao

DOI: https://doi.org/10.1016/j.gee.2020.06.011

IF: 12.781

2020-01-01

Green Energy & Environment

Abstract:Operating chemical looping process at mid-temperatures (550–750 °C) presents exciting potential for the stable production of hydrogen. However, the reactivity of oxygen carriers is compromised by the detrimental effect of the relatively low temperatures on the redox kinetics. Although the reactivity at mid-temperature can be improved by the addition of noble metals, the high cost of these noble metal containing materials significantly hindered their scalable applications. In the current work, we propose to incorporate earth-abundant metals into the iron-based spinel for hydrogen production in a chemical looping scheme at mid-temperatures. Mn0.2Co0.4Fe2.4O4 shows a high hydrogen production performance at the average rate of ∼0.62 mmol g−1 min−1 and a hydrogen yield of ∼9.29 mmol g−1 with satisfactory stability over 20 cycles at 550 °C. The mechanism studies manifest that the enhanced hydrogen production performance is a result of the improved oxygen-ion conductivity to enhance reduction reaction and high reactivity of reduced samples with steam. The performance of the oxygen carriers in this work is comparable to those noble-metal containing materials, enabling their potential for industrial applications.
Chemical Looping Hydrogen Storage and Production: Use of Binary Ferrite-Spinel As Oxygen Carrier Materials

Min Li,Yu Qiu,Li Ma,Dongxu Cui,Shuai Zhang,Dewang Zeng,Rui Xiao

DOI: https://doi.org/10.1039/c9se01104h

IF: 6.813

2020-01-01

Sustainable Energy & Fuels

Abstract:Co0.25Fe2.75O4 exhibits a high reduction level and reversibility of phase changes, which benefits the hydrogen storage capacity at intermediate temperatures.
Ternary Mixed Spinel Oxides As Oxygen Carriers for Chemical Looping Hydrogen Production Operating at 550 °C

Dewang Zeng,Yu Qiu,Min Li,Dongxu Cui,Li Ma,Yulin Lv,Shuai Zhang,Rui Xiao

DOI: https://doi.org/10.1021/acsami.9b14989

IF: 9.5

2019-01-01

ACS Applied Materials & Interfaces

Abstract:Operating chemical looping at moderate temperatures circumvents the issue that the sintering of oxygen carrier materials is serious at typical operating conditions, 800-950 °C. However, lower temperatures can lead to deterioration on the reaction kinetics and thereby the low H2 production rate and yield. Here, we present several doped spinel oxides consisting of earth-abundant elements for chemical looping water splitting. By virtue of the ability of the Cu dopant to improve the reduction of the Co-based binary spinel, the high reducibility of the dopants in the reduction period, as well as the phase reversibility in the water splitting period, Cu0.25Co0.25Fe2.5Oy shows a high hydrogen yield (∼11.9 mmol g-1) and an average hydrogen production rate (∼137.7 μmol g-1 min-1) at 550 °C, with negligible decays in repetitive redox cycles. The performance of this material is comparable to that of the state-of-the-art perovskites which usually contain rare-earth metals, enabling its potential in industrial implementation.
Synergistic Effects of Binary Oxygen Carriers During Chemical Looping Hydrogen Production

Dewang Zeng,Yu Qiu,Shuai Zhang,Li Ma,Min Li,Dongxu Cui,Jimin Zeng,Rui Xiao

DOI: https://doi.org/10.1016/j.ijhydene.2019.06.118

IF: 7.2

2019-01-01

International Journal of Hydrogen Energy

Abstract:The use of binary oxygen carrier allows for the materials of enhanced activity or stability during chemical looping process. However, the lack of mechanical understanding of the origin of the improvements hindered the rational design and control of the doping process in the oxygen carrier production. Here, we synthesized a series of M0.6Fe2.4Oy (M = Ni, Cu, Co, Mn) binary spinel materials and carried out various characterization techniques to study how the dopants influenced the material phase change, the oxygen transfer as well as the chemical looping performance. The results showed the chemical looping reactivity can be related to the oxygen transformation between lattice oxygen and oxygen vacancy, which was determined by the redox properties of both dopants and iron. The metal in tetrahedral site for Cu, Mn, Ni-doped sample were relatively stable, limiting oxygen transformation ability. In comparison, Co dopant promoted the reducibility of iron in tetrahedral site as well as metals in other sites, making almost all lattice oxygen rapidly transformed to oxygen vacancy during reduction. This was the main cause for the subsequent high hydrogen production rate (average similar to 0.02 mmol. g(-1).s(-1)) and yield (similar to 15.9 mmol.g(-1)). Upon cycling, the phase separation of single oxides from Co0.6Fe2.4Oy and Mn0.6Fe2.4Oy spinels led to the decreased ability of oxygen transformation. However, the performance was extremely stable for Cu0.6Fe2.4Oy with reversible phase change between spinel and (Fe, Cu) wusitite by the Cu-Fe interaction. Based on the current results, this work points to a promising Cu-Co co-doping material with both good reactivity and stability. (C) 2019 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
Enhanced Hydrogen Production Performance at Intermediate Temperatures Through the Synergistic Effects of Binary Oxygen Carriers

Yu Qiu,Shuai Zhang,Dongxu Cui,Min Li,Jimin Zeng,Dewang Zeng,Rui Xiao

DOI: https://doi.org/10.1016/j.apenergy.2019.113454

IF: 11.2

2019-01-01

Applied Energy

Abstract:Operating oxygen carrying materials under a relatively low temperature has been the most important goal for the scalable application of chemical looping hydrogen production, so as to increase the durability and process economy. However, low temperatures have a degrading effect on the kinetics of the redox reactions, when it comes to the hydrogen production, leading to decreased oxygen storage capacity and thereby the low hydrogen yield and production rate. Although improved performance at intermediate temperatures can be found in materials composed of rare earth oxides, the high cost hindered the industrial application of these materials. In this paper, we prepared a series of binary oxygen carrier materials (CoFeOy, NiFeOy, CuFeOy) and investigated the chemical looping hydrogen production performance at intermediate temperatures. CoFeOy exhibited the highest hydrogen yield (similar to 11.17 mmol g(-1)) and peak hydrogen production rate (similar to 0.23 mmol g(-1) s(-1)) at 650 degrees C. To explore the synergistic effects causing the improved performance, XPS and TPR study was carried out. The results exhibited that the full reduction of Fe3O4 to FeO can be found at similar to 800 degrees C for CoFeOy, whist Co dopant was highly reducible with reversible phase change in the whole redox period at the intermediate temperature. The redox chemistry obtained in this work can be helpful for the design of the oxygen carrier materials for low temperature chemical looping applications.
Engineering high-spin state cobalt cations in spinel ZnCo2O4 for spin channel propagation and electrocatalytic activity enhancement in Li-O2 battery

Longfei Ren,Xiaojuan Wen,Dayue Du,Yu Yan,Haoyang Xu,Ting Zeng,Chaozhu Shu

DOI: https://doi.org/10.1016/j.cej.2023.142288

IF: 15.1

2023-04-15

Chemical Engineering Journal

Abstract:Spinel zinc cobalt oxide (ZnCo2O4) is considered as the promising electrocatalyst for the electrochemical oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). However, theoretical calculations uncovered that the presence of low-spin (LS) state cobalt cations impedes the electrocatalytic activity of ZnCo2O4 because the t2g6eg0 configuration yields purely localized electronic structure with poor binding affinity with reaction intermediate. By regulating the spin state of cobalt cations in ZnCo2O4, spin-selected charge transfer is boosted during ORR/OER processes due to the propagated spin channel, thus causing abundant active sites for intermediates adsorption. Experimental results show that increasing calcination temperature during the synthesis process is an operable method to fabricate high-spin (HS) cobalt cations in ZnCo2O4. And the Li-O2 battery with ZnCo2O4 containing high-spin cobalt cations shows remarkably low overpotential of only 0.45 V and excellent durability of more than 800 h. This work underlines the critical role of the electron spin state in facilitating oxygen redox reactions on transition metal oxides.

engineering, chemical, environmental
A High-Performance Ternary Ferrite-Spinel Material for Hydrogen Storage Via Chemical Looping Redox Cycles

Dewang Zeng,Min Li,Yu Qiu,Li Ma,Dongxu Cui,Shuai Zhang,Rui Xiao

DOI: https://doi.org/10.1016/j.ijhydene.2019.11.021

IF: 7.2

2019-01-01

International Journal of Hydrogen Energy

Abstract:Chemical looping has been proposed as an emerging technology for large-scale hydrogen storage with the advantages of high volumetric hydrogen storage density, environmental compatibility, and safety. However, to ensure sufficient redox activity, conventional oxygen carrier materials must be operated at a temperature higher than 800 degrees C, leading to the rapid deterioration on the storage capacity over several cycles. In this work, we report a ternary ferrite-spinel material Cu0.5Co0.5Fe2O4 for chemical looping hydrogen storage and production. The material exhibits high volumetric hydrogen storage density (65.58 g.L-1) and average hydrogen production rate (142 mu mol.g(-1).min(-1)) at 550 degrees C. The performance is maintained with negligible deactivation over repetitive redox cycles. The high performance can be attributed to the ability of Cu and Co to improve the reduction and the reversible phase change during the oxidation stage at moderate temperatures. The performance of the Cu0.5Co0.5Fe2O4 is comparable to the state-of-the-art Rh-FeOx containing rare earth metals, which enables its potential in industry application. (C) 2019 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.
Efficient CO 2 to CO Conversion at Moderate Temperatures Enabled by the Cobalt and Copper Co-Doped Ferrite Oxygen Carrier

Yu Qiu,Li Ma,Dewang Zeng,Min Li,Dongxu Cui,Yulin Lv,Shuai Zhang,Rui Xiao

DOI: https://doi.org/10.1016/j.jechem.2019.10.025

IF: 13.1

2019-01-01

Journal of Energy Chemistry

Abstract:Chemical looping technology holds great potential on efficient CO2 splitting with much higher CO production and CO2 splitting rate than photocatalytic processes. Conventional oxygen carrier requires high temperature (typically 850-1000 degrees C) to ensure sufficient redox activity, but the stable and high CO2 conversion is favored at a lower temperature, leading to the degrading on the reaction kinetics as well as the low CO production and CO2 splitting rate. In this paper, we prepared several ternary spinels and demonstrated their performance for chemical looping CO2 splitting at moderate temperatures. Using the promotion effect of Cu to cobalt ferrite reduction and reversible phase change of the reduced metals, Cu 0.4 Co 0.6 Fe2O4 exhibits high CO2 splitting rate (similar to 144.6 mu mol g(-1) min(-1)) and total CO production (similar to 9100 mu mol g(-1)) at 650 degrees C. The high performance of this earth-abundant spinel material is also consistent in repeated redox cycles, enabling their potential in industrial use. (C) 2019 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.
Copper and Cobalt Co-Doped Ferrites As Effective Agents for Chemical Looping CO2 Splitting

Yu Qiu,Li Ma,Min Li,Dongxu Cui,Shuai Zhang,Dewang Zeng,Rui Xiao

DOI: https://doi.org/10.1016/j.cej.2020.124150

IF: 15.1

2020-01-01

Chemical Engineering Journal

Abstract:The sintering of oxygen carrier materials can be circumvented by operating chemical looping at relatively low temperatures ( < 750 degrees C). However, low temperature has a degrading effect on the redox kinetics of the materials and thereby limited efficiencies. In the current work, we report several Co, Cu co-doped spinel-structured ferrites as effective redox materials in the chemical looping scheme for CO2 thermo splitting at 650 degrees C. Cu0.2Co0.8Fe2O4 presents high average CO2 splitting rate of similar to 144.9 mu mol.g(-1).min(-1) and CO yield of similar to 9.0 mmol.g(-1) with satisfactory stability over cyclic redox operations. The improved performance can be attributed to the improved reduction of iron oxides by Cu, Co co-dopant, and the reversible phase change of the reduced sample in the CO2 splitting stage. Additionally, increasing Cu doping amount leads to the formation of insufficiently active impurities which is unfavorable for the CO2 thermo-splitting. The synergy in this work can be helpful for the design of the redox materials at moderate temperatures.
Efficient Hydrogen Production Through the Chemical Looping Redox Cycle of YSZ Supported Iron Oxides

Li Ma,Yu Qiu,Min Li,Dongxu Cui,Shuai Zhang,Dewang Zeng,Rui Xiao

DOI: https://doi.org/10.1016/j.gee.2020.06.023

IF: 12.781

2020-01-01

Green Energy & Environment

Abstract:The chemical looping process,where an oxygen carrier is reduced and oxidized in a cyclic manner,offers a promising option for hydrogen production through splitting water because of the much higher water splitting efficiency than solar electrocatalytic and photocatalytic process.A typical oxygen carrier has to comprise a significant amount of inert support,to maintain stability in multiple redox cycles,thereby resulting in a trade-off between the reaction reactivity and stability.Herein,we proposed the use of ion-conductive yttria-stabilized zirconia (YSZ) support Fe2O3 to prepare oxygen carriers materials.The obtained Fe2O3/YSZ composites showed high reactivity and stability.Particularly,Fe2O3/YSZ-20 (oxygen storage capacity,24.13％) exhibited high hydrogen yield of ～10.30 mmol g 1 and hydrogen production rate of ～0.66 mmol g 1 min-1 which was twice as high as that of Fe2O3/Al2O3.Further,the transient pulse test indicated that active oxygen diffusion was the rate-limiting step during the redox process.The electrochemical impedance spectroscopy (EIS) measurement revealed that the YSZ support addi-tion facilitated oxygen diffusion of materials,which contributed to the improved hydrogen production performance.The support effect obtained in this work provides a potentially efficient route for the modification of oxygen carrier materials.
Phase and composition controllable synthesis of cobalt manganese spinel nanoparticles towards efficient oxygen electrocatalysis

Chun Li,Xiaopeng Han,Fangyi Cheng,Yuxiang Hu,Chengcheng Chen,Jun Chen

DOI: https://doi.org/10.1038/ncomms8345

IF: 16.6

2015-06-04

Nature Communications

Abstract:Spinel-type oxides are technologically important in many fields, including electronics, magnetism, catalysis and electrochemical energy storage and conversion. Typically, these materials are prepared by conventional ceramic routes that are energy consuming and offer limited control over shape and size. Moreover, for mixed-metal oxide spinels (for example, CoxMn3−xO4), the crystallographic phase sensitively correlates with the metal ratio, posing great challenges to synthesize active product with simultaneously tuned phase and composition. Here we report a general synthesis of ultrasmall cobalt manganese spinels with tailored structural symmetry and composition through facile solution-based oxidation–precipitation and insertion–crystallization process at modest condition. As an example application, the nanocrystalline spinels catalyse the oxygen reduction/evolution reactions, showing phase and composition co-dependent performance. Furthermore, the mild synthetic strategy allows the formation of homogeneous and strongly coupled spinel/carbon nanocomposites, which exhibit comparable activity but superior durability to Pt/C and serve as efficient catalysts to build rechargeable Zn–air and Li–air batteries.

multidisciplinary sciences
Spinel Nanostructures for the Hydrogenation of CO2 to Methanol and Hydrocarbon Chemicals

Mengheng Wang,Lanling Zheng,Genyuan Wang,Jiale Cui,Gui-Ling Guan,Yu-Ting Miao,Jian-Feng Wu,Pan Gao,Fan Yang,Yunjian Ling,Xiangxue Luo,Qinghong Zhang,Gang Fu,Kang Cheng,Ye Wang

DOI: https://doi.org/10.1021/jacs.4c00981

2024-05-29

Abstract:Composite oxides have been widely applied in the hydrogenation of CO/CO2 to methanol or as the component of bifunctional oxide-zeolite for the synthesis of hydrocarbon chemicals. However, it is still challenging to disentangle the stepwise formation mechanism of CH3OH at working conditions and selectively convert CO2 to hydrocarbon chemicals with narrow distribution. Here, we investigate the reaction network of the hydrogenation of CO2 to methanol over a series of spinel oxides (AB2O4), among which the Zn-based nanostructures offer superior performance in methanol synthesis. Through a series of (quasi) in situ spectroscopic characterizations, we evidence that the dissociation of H2 tends to follow a heterolytic pathway and that hydrogenation ability can be regulated by the combination of Zn with Ga or Al. The coordinatively unsaturated metal sites over ZnAl2Ox and ZnGa2Ox originating from oxygen vacancies (OVs) are evidenced to be responsible for the dissociative adsorption and activation of CO2. The evolution of the reaction intermediates, including both carbonaceous and hydrogen species at high temperatures and pressures over the spinel oxides, has been experimentally elaborated at the atomic level. With the integration of a series of zeolites or zeotypes, high selectivities of hydrocarbon chemicals with narrow distributions can be directly produced from CO2 and H2, offering a promising route for CO2 utilization.
Entropy-Stabilized Multicomponent Porous Spinel Nanowires of NiFeXO 4 (X = Fe, Ni, Al, Mo, Co, Cr) for Efficient and Durable Electrocatalytic Oxygen Evolution Reaction in Alkaline Medium

Qiwen Zhang,Yixuan Hu,Haofei Wu,Xiaoran Zhao,Mingliang Wang,Sihong Wang,Ruohan Feng,Qing Chen,Fang Song,Mingwei Chen,Pan Liu

DOI: https://doi.org/10.1021/acsnano.2c10247

IF: 17.1

2023-01-13

ACS Nano

Abstract:Cost-effective electrochemical water splitting technology hinges on the development of efficient and durable catalysts for oxygen evolution reaction (OER). Spinel oxides (formula: A(x)B(3-x)O(4)) are structurally stable for real applications. Much effort has been devoted to improving the catalytic activity. Here, we report a eutectic dealloying strategy to activate the porous spinel NiFe(2)O(4) nanowires with up to four metal cation substitutions. As-obtained spinel NiFeXO(4) (X = Fe, Ni, Al,...

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology
Spinel-Structured Ternary Ferrites As Effective Agents for Chemical Looping CO2 Splitting

Li Ma,Yu Qiu,Min Li,Dongxu Cui,Shuai Zhang,Dewang Zeng,Rui Xiao

DOI: https://doi.org/10.1021/acs.iecr.9b06799

2020-01-01

Industrial & Engineering Chemistry Research

Abstract:Reverse water gas shift on the basis of chemical looping technology provides a viable method for efficiently converting CO2 to CO for hydrocarbons at moderate temperature (<750 degrees C). However, the commonly available oxygen carrier materials are insufficiently active because of the degrading effect at relatively low temperatures. In this paper, we present several Co, Mn codoped ferrites in search of oxygen carrier materials as highly active redox materials for a midtemperature chemical looping CO2 splitting process. The results show that up to similar to 142.3 mu mol.g(-1). min(-1) of CO production rate and similar to 8.8 mmol.g(-1) of CO yield are achieved by Mn0.2Co0.8Fe2O4 at 650 degrees C. The production rate and yield of CO of the codoped ferrites during the CO2 splitting process are comparable to those of the state-of-the-art perovskites which commonly contain rare-metal elements.
Highly sintering-resistant iron oxide with a hetero-oxide shell for chemical looping water splitting

Iwei Wang,Lei Liu,Shuyao Yu,Nien-Chu Lai,Yunfei Gao,Zhenshan Li,Jianguo Liu,Wei Wang

DOI: https://doi.org/10.1016/j.ijhydene.2024.01.051

IF: 7.2

2024-01-18

International Journal of Hydrogen Energy

Abstract:Chemical looping water splitting is a promising technology that couples carbonaceous fuel oxidation to produce H 2 with inherent CO 2 separation. Redox catalyst with long-term performance is the key issue but is hampered in traditional Fe 2 O 3 -based approaches due to Fe sintering. This study reports a one-step sol-gel synthetic method to construct Fe 2 O 3 @Hetero-oxide redox catalysts with core-shell structure, leading to outstanding anti-sintering property in TGA analysis (>250 cycles, 5000 min). Fixed-bed reactor tests showed that hydrogen yield approached theoretical value (16.7 mmol/g-Fe 2 O 3 ), with ∼100 % H 2 purity. This result is significantly better than dispersing a mixed ionic-electronic conductor (MIEC) in Fe 2 O 3 matrix using high energy ball milling. Although the latter can enhance the durability due to facilitated O 2− and electron transportation, Fe sintering and redox catalysts deactivation is inevitable. This study offers a generalized structure design and synthetic approach for anti-sintering redox catalysts within chemical looping concepts.

energy & fuels,electrochemistry,chemistry, physical
Regulating the Spin State of Metal and Metal Carbide Heterojunctions for Efficient Oxygen Evolution

Shan Ni,Hongnan Qu,Zihao Xu,Xiangyang Zhu,Liyan Chen,Huifang Xing,Xia Wu,Huizhou Liu,Liangrong Yang

DOI: https://doi.org/10.1021/acsami.3c07955

IF: 9.5

2023-07-20

ACS Applied Materials & Interfaces

Abstract:Developing high-performance electrocatalysts for oxygen evolution reaction (OER) is of importance for improving the overall efficiency of water splitting. Herein, the CoFe/(Co(x)Fe(1-x))(3)Mo(3)C heterojunction is purposely designed as an OER catalyst, which displays a low overpotential of 293 mV for affording a current density of 10 mA cm^(-2) and a small Tafel slope of 48 mV/dec. Various characterization results demonstrate that the significant work-function difference between CoFe and...

materials science, multidisciplinary,nanoscience & nanotechnology
Manipulating the Spin State of Spinel Octahedral Sites via a π‐π Type Orbital Coupling to Boost Water Oxidation

Zhangtao Guo,Qian Zhu,Shaohua Wang,Mengpei Jiang,Xinxin Fan,Wanyu Zhang,Mei Han,Xiaotian Wu,Xiangyan Hou,Yaowen Zhang,Zhiyu Shao,Jingyu Shi,Xia Zhong,Shuting Li,Xiaofeng Wu,Keke Huang,Shouhua Feng

DOI: https://doi.org/10.1002/anie.202406711

2024-06-26

Angewandte Chemie International Edition

Abstract:Spin state is often regarded as the crucial valve to release the reactivity of energy-related catalysts, yet it is also challenging to precisely manipulate, especially for the active center ions occupied at the specific geometric sites. Herein, a π-π type orbital coupling of 3d (Co)-2p (O)-4f (Ce) was employed to regulate the spin state of octahedral cobalt sites (CoOh) in the composite of Co3O4/CeO2. More specifically, the equivalent high-spin ratio of CoOh can reach to 54.7% via tuning the CeO2 content, thereby triggering the average eg filling (1.094) close to the theoretical optimum value. The corresponding catalyst exhibits a superior water oxidation performance with an overpotential of 251 mV at 10 mA cm-2, rivaling most cobalt-based oxides state-of-the-art. The π-π type coupling corroborated by the matched energy levels between Ce t1u/t2u-O and CoOh t2g-O π type bond in the calculated crystal orbital Hamilton population and partial density of states profiles, stimulates a π-donation between O 2p and π-symmetric Ce 4fyz2 orbital, consequently facilitating the electrons hopping from t2g to eg orbital of CoOh. This work offers an in-depth insight into understanding the 4f and 3d orbital coupling for spin state optimization in composite oxides.

chemistry, multidisciplinary

Enhanced Hydrogen Production Performance Through Controllable Redox Exsolution Within CoFeAlOx Spinel Oxygen Carrier Materials

Cu–Fe–Al–O Mixed Spinel Oxides As Oxygen Carrier for Chemical Looping Hydrogen Generation

A Mixed Spinel Oxygen Carrier with Both High Reduction Degree and Redox Stability for Chemical Looping H2 Production

Mn-Fe-Al-O Mixed Spinel Oxides As Oxygen Carrier for Chemical Looping Hydrogen Production with CO2 Capture

Earth Abundant Spinel for Hydrogen Production in a Chemical Looping Scheme at 550 °C

Chemical Looping Hydrogen Storage and Production: Use of Binary Ferrite-Spinel As Oxygen Carrier Materials

Ternary Mixed Spinel Oxides As Oxygen Carriers for Chemical Looping Hydrogen Production Operating at 550 °C

Synergistic Effects of Binary Oxygen Carriers During Chemical Looping Hydrogen Production

Enhanced Hydrogen Production Performance at Intermediate Temperatures Through the Synergistic Effects of Binary Oxygen Carriers

Engineering high-spin state cobalt cations in spinel ZnCo2O4 for spin channel propagation and electrocatalytic activity enhancement in Li-O2 battery

A High-Performance Ternary Ferrite-Spinel Material for Hydrogen Storage Via Chemical Looping Redox Cycles

Efficient CO 2 to CO Conversion at Moderate Temperatures Enabled by the Cobalt and Copper Co-Doped Ferrite Oxygen Carrier

Copper and Cobalt Co-Doped Ferrites As Effective Agents for Chemical Looping CO2 Splitting

Efficient Hydrogen Production Through the Chemical Looping Redox Cycle of YSZ Supported Iron Oxides

Phase and composition controllable synthesis of cobalt manganese spinel nanoparticles towards efficient oxygen electrocatalysis

Spinel Nanostructures for the Hydrogenation of CO2 to Methanol and Hydrocarbon Chemicals

Entropy-Stabilized Multicomponent Porous Spinel Nanowires of NiFeXO 4 (X = Fe, Ni, Al, Mo, Co, Cr) for Efficient and Durable Electrocatalytic Oxygen Evolution Reaction in Alkaline Medium

Spinel-Structured Ternary Ferrites As Effective Agents for Chemical Looping CO2 Splitting

Highly sintering-resistant iron oxide with a hetero-oxide shell for chemical looping water splitting

Regulating the Spin State of Metal and Metal Carbide Heterojunctions for Efficient Oxygen Evolution

Manipulating the Spin State of Spinel Octahedral Sites via a π‐π Type Orbital Coupling to Boost Water Oxidation