Abstract:Magnesium alloys with excellent degradability and biocompatibility are promising materials for biomedical implants, saving patients the burden of second surgeries. However, their mechanical properties and corrosion resistance are significantly below the requirements for implant applications. This study aims to improve the mechanical and corrosion resistance properties of Mg-3Zn-0.2Ca alloy by pre-torsion treatment, and find out the optimal shear strain. The rod-shaped Mg-3Zn-0.2Ca alloy specimens were pre-torsion treated at different torsion angles. The effect of free-end torsion on Mg-3Zn-0.2Ca alloy was characterized through microstructure analysis, mechanical testing, and corrosion testing. Pre-torsion treatment can refine grain and induce twins and dislocations in Mg-3Zn-0.2Ca alloy. The surface hardness increases with the increase in torsion angle. Tensile yield strength and ultimate strength initially increase and then decrease with increasing torsion angle, while ductility decreases with increasing torsion angle. Specimens with a shear strain of 30% exhibit the highest tensile strength, reaching 284.78 ± 10.62 MPa, with an elongation of 19.37 ± 1.66%. Furthermore, they show a significant improvement in fatigue lives both before and after pre-corrosion. When the stress amplitude is 120 MPa, the fatigue lives for specimens without pre-torsion treatment are 54,275 cycles and 4324 cycles before and after pre-corrosion, while they increased significantly to 92,015 cycles and 5050 cycles with the 30% shear strain, respectively. Additionally, the 30% shear strain specimens show a significant reduction in corrosion rates. In conclusion, pre-torsion treatment can effectively modify the microstructure of Mg-3Zn-0.2Ca alloy, enhancing both mechanical properties and corrosion resistance. The optimal shear strain for this improvement is 30%. This study provides a practical method to enhance the mechanical properties and corrosion resistance of Mg-3Zn-0.2Ca alloy, making it more suitable for biomedical implant applications.

Effects of Free-End Torsion on the Microstructure Evolution and Fatigue Properties in an Extruded AZ31 Rod

Influence of Pre-Tension on Free-End Torsion Behavior and Mechanical Properties of an Extruded Magnesium Alloy.

Twinning Deformation and Yield Asymmetry Improvement of Magnesium Alloys by Free-End Torsion

Formation of Gradient Microstructure and Elimination of Tension-Compression Yield Asymmetry of the Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy Via Free-End Torsion

Improving tensile and compressive properties of magnesium alloy rods via a simple pre-torsion deformation

Influence of Torsion Route on the Microstructure and Mechanical Properties of Extruded AZ31 Rods

Influence of direct extrusion and torsional deformation on microstructure and properties of magnesium alloys

Improving Tensile and Compressive Properties of an Extruded AZ91 Rod by the Combined Use of Torsion Deformation and Aging Treatment

Preparation and Characterization of Mg Alloy Rods with Gradient Microstructure by Torsion Deformation

Effect of Free-End Torsion on the Corrosion and Mechanical Properties for Mg-3Zn-0.2Ca Alloy

The effect of pre-twinning on the mechanical behavior of free-end torsion for an extruded AZ31 magnesium alloy

Influence of Deformation Prior to Ageing on Fatigue Behavior of Extruded AA6082-T6 Profiles

Second-order Deformation Behaviors of Free-Rotational Tension after Free-End Torsion for Rolled AZ31B Magnesium Alloy

Influence of Torsion on Precipitation and Hardening Effects During Aging of an Extruded AZ91 Alloy

Effect of Free-End Torsion on Microstructure and Mechanical Properties of AZ31 Bars with Square Section

Effect of Strain Reversal on Microstructure and Mechanical Properties of Ti-6Al-4V Alloy under Cyclic Torsion Deformation

Effects of texture and twinning on the torsional behavior of magnesium alloy solid rod: A crystal plasticity approach in comparison with uniaxial tension/compression

Microstructures and Mechanical Properties of Commercial Hot‐Extruded Copper Processed by Torsion Deformation

Strengthening and toughening of extruded magnesium alloy rods by combining pre-torsion deformation with subsequent annealing

Effects of Micro-Twin Lamellar Structure on the Mechanical Properties and Fracture Morphology of AZ31 Mg Alloy

Effect of initial orientation on the microstructure and mechanical properties of textured AZ31 Mg alloy during torsion and annealing