Abstract:Taking into account the local stresses resulting from the primary twinning with transformation strains, the competition between double twinning {10–11}–{10–12} and (10–12)–(–1012) (CDTW and EDTW) is theoretically modeled. Using electron backscatter diffraction technique, the statistical fractions, thickness-length ratios and their critical values of CDTW and EDTW within grains of as-cast AZ31 magnesium alloy sheets at the low strain stage of hot rolling processing are obtained to validate the theoretical results. In addition, the competition between the DTW and twin intersection are also discussed in detail. The results show that: (1) The secondary twin growth complies with the classical Hall-Petch relationship. Due to the difference in the driving forces resulting from different transformation strains between the primary extension and contraction twinning, the secondary extension twin of EDTW is more difficult to grow compared to that of CDTW for primary twin bands with small thickness-length ratios, which is contrary to the regulation for primary twin bands with large thickness-length ratios; (2) The greater the thickness-length ratio of the primary twinning is, the smaller the critical shear stress of the secondary twinning is. This is opposite to the effect of thickness-length ratio on the critical shear stress of the incident twinning in the twin intersection. It is indicated that the thickening of the primary twinning provides the higher driving force for the formation of DTW, however hinders the twin intersection more evidently; (3) Within coarse grains, at the low strain stage, the formation of DTW can dominantly induce dynamic recrystallization and continue plastic deformation, while the stress concentration resulting from the twin intersection is inclined to cause brittle fracture. Therefore, based on the effect of the local stress, the selection mechanism of the thickness-length ratio on the DTW and twin intersection is of great significance to determining the plastic performance of magnesium alloys during hot working. In the current study, massive control factors of the thickness-length ratio of the primary twinning are concluded, which provides some corresponding schemes of material design.

The effect of pre-twinning on the mechanical behavior of free-end torsion for an extruded AZ31 magnesium alloy

Influence of initial {10−12} twins on twinning behavior of extruded AZ31 alloys during free-end torsion

Influence of In-Plane Simple Shear Strain on the Grain Orientation Regulation and Stretch Formability of Pre-twinned AZ31 Magnesium Alloy Sheet

Effect of pre-deformation on the activation stress of {10–12} twinning in Mg–3Al–1Zn alloy

Numerical Study on the Effect of Pre-Strain on Detwinning in Rolled Mg Alloy AZ31

Effect of Local Stresses of Primary Twinning on Double Twinning, Twin Intersection and Their Competition

Effect of deformation conditions on twinning of AZ31 magnesium alloy during compression test

Research on deformation mechanism of AZ31 magnesium alloy during uniaxial compression

The effects of orientation control via tension-compression on microstructural evolution and mechanical behavior of AZ31 Mg alloy sheet

Study of Twin Behavior During Uniaxial Compression of Az31 Magnesium Alloy

Effect of large pre-deformation on the microstructure, texture and mechanical properties of Al-Zn-Mg alloy extruded profiles

Effect of twins and plastic-deformation anisotropy of extruded magnesium alloy on fatigue crack growth and crack closure behavior

Effect of twinning on the deformation behavior of an extruded Mg-Zn-Zr alloy during hot compression testing

Effects of Twin-Dislocation and Twin-Twin Interactions on the Strain Hardening Behavior of TWIP Steels

Influence of Local Strain on Twinning Behavior During Compression of AZ31 Magnesium Alloy

Effect of Pulsed Current on the Tensile Deformation Behavior and Microstructure Evolution of AZ80 Magnesium Alloy

Improvement of dynamic compression properties and strengthening mechanism of Mg–Y–Nd–Gd–Zr alloy by pre-twinning

Effect of Pre-Stretching Process on Quenching Residual Stress of Ew75 Magnesium Alloy

Improving mechanical properties of AZ31 alloy sheets via novel turned-bearing extrusion by introducing shear strain

Effect of Free-End Torsion on the Corrosion and Mechanical Properties for Mg-3Zn-0.2Ca Alloy

Influence of precipitation on tension and compression twinning in Mg-6.5Zn alloy