Abstract:In this study, the formation processes of TiC in a Cu–Ti–SiC system following the addition of a Ti–SiC mixture into a Cu melt were studied by analyzing the reaction intermediates, and the influence of the synthesis processes on the TiC microstructure was examined. It is found that, upon the addition of Ti–SiC into the Cu melt, the reaction of Ti and Cu to form a Cu–Ti liquid phase occurred first, followed by the reaction between liquid Ti, denoted as Ti(l), and SiC. However, the Ti(l)–SiC reaction processes vary depending on the reaction conditions and significantly influence the microstructures of the TiC particles, especially their dispersion in the Cu matrix. Under certain conditions, such as a lower reaction temperature and larger SiC size, SiC does not directly react with Ti(l). It first transforms into graphite through the outward diffusion of Si; subsequently, the graphite phase reacts with Ti(l) to form TiC. In this case, the synthesized TiC particles tend to connect with each other to form agglomerates. Under conditions conducive to the direct reaction of the Ti(l)–SiC system, such as a higher reaction temperature and smaller SiC size, Ti(l) and SiC first react to form a Ti3SiC2 phase that then decomposes into TiCx and Ti–Si phases and eventually transforms into TiCy (x > y) and amorphous or crystalline Si. In this case, the formed Ti–Si or Si phase can prevent the agglomeration of TiC particles, leading to their more uniform distribution in the prepared Cu matrix composite.

Effects of Carbon Content and Size on Ti-C Reaction Behavior and Resultant Properties of Cu-Ti-C Alloy System

Effects of Process Parameters on Microstructure and Properties of TiC Reinforced Cu-Matrix Composites

Effect of Cu-Ti-C Reaction Composition on Reinforcing Particles Size of TiCx/Cu Composites

Interaction of a Ti⁻Cu Alloy with Carbon: Synthesis of Composites and Model Experiments

Effect of TiC Particle Size on the Microstructure and Properties of CuCr-TiC Composites Manufactured by Powder Metallurgy

The microstructures of in-situ synthesized TiC by Ti-CNTs reaction in Cu melts

Mechanical milling and its influence on microstructure and electric conductivity of high mass fraction TiC / Cu composites

Effect of Carbon Reactant on Microstructures and Mechanical Properties of Tial/Ti2alc Composites

Effect of TiC Content on Microstructure and Mechanical Properties of High-temperature Titanium Matrix Composites

Effect of Carbon on the Microstructure and Element Distribution in Ti42Al5Mn Alloy

Effect of Ti–Cu alloy's composition on microstructure and performance of carbon fiber reinforced TiC-based composites prepared by alloyed reactive melt infiltration

Influence of TiC particle size on microstructural evolution and fracture mechanism of TiC/Al-Cu composites

Physical, mechanical, and ablation properties of Cu–Ti3AlC2 composites with various Ti3AlC2 contents

Microstructure Characterization of the Cu-Ti-C Composites Prepared by Mechanical Alloying and Spark Plasma Sintering

Influence on TiC microstructure from different synthesis processes in the Cu–Ti–SiC system

Size effect of B 4 C powders on metallurgical reaction and resulting tensile properties of Ti matrix composites by in-situ reaction from Ti–B 4 C system under a relatively low temperature

Effect of Ti on Interface Wettability and Microstructure of C/Cu Composites Prepared by Infiltration

Effect of Ti<sub>3</sub>SiC<sub>2</sub> Content on the Property of a Warm Compacted Cu-Ti<sub>3</sub>SiC<sub>2</sub> Composite

Effects of Alloying Ti on Thermal Conductivity of C/Cu Composite Prepared by Pressureless Infiltration

Influence of Cu Content on the Microstructure and Mechanical Property of Ti3SiC2/Cu Composites

Investigation on microstructure and properties of TiC0.5-Al2O3/Cu composites fabricated by a novel in-situ reactive synthesis