Abstract:A relative thin photoanode prepared by the cationic surfactant-assisted multiple deposition procedure has achieved a high QD loading which is comparable to that of the thick photoanode commonly used.Under AM 1.5G illumination, Zn−Cu−In−Se and Zn−Cu−In−S based QDSCs with optimized 11.8 μm photoanodes show the PCE of 10.03% and 8.53%, respectively, which are comparable to the corresponding highest PCE of Zn−Cu−In−Se and Zn−Cu−In−S QDSCs (9.74% and 8.75%) with over 25.0 μm photoanodes.An impressive PCE of 6.14% was obtained for the CdSe based QDSCs with a 4.1 μm photoanode, which is slightly lower than the best PCE (7.05%) of reference CdSe QDSCs with 18.1 μm photoanode.The results implied that the manufacturing cost of QDSCs could be reduced.High light-harvesting efficiency and low interfacial charge transfer loss are essential for the fabrication of high-efficiency quantum dot-based solar cells (QDSCs). Increasing the thickness of mesoporous TiO2 films can improve the loading of pre-synthesized QDs on the film and enhance the absorbance of photoanode, but commonly accompanied by the increase in the unfavorable charge recombination due to prolonged electron transmission paths. Herein, we systematically studied the influence of the balance between QD loading and TiO2 film thickness on the performance of QDSCs. It is found that the relative thin photoanode prepared by the cationic surfactant-assisted multiple deposition procedure has achieved a high QD loading which is comparable to that of the thick photoanode commonly used. Under AM 1.5G illumination, Zn−Cu−In−Se and Zn−Cu−In−S based QDSCs with optimized 11.8 μm photoanodes show the PCE of 10.03% and 8.53%, respectively, which are comparable to the corresponding highest PCE of Zn−Cu−In−Se and Zn−Cu−In−S QDSCs (9.74% and 8.75%) with over 25.0 μm photoanodes. Similarly, an impressive PCE of 6.14% was obtained for the CdSe based QDSCs with a 4.1 μm photoanode, which is slightly lower than the best PCE (7.05%) of reference CdSe QDSCs with 18.1 μm photoanode.By controlling the times of HTAC assisted depositions, the performance of an optimized QD/nH/QD photoanode with a thin photoanode is close to or slightly lower than that of the thick reference one<ol class="links-for-figure"><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S2468025721000649-ga1_lrg.jpg">Download : Download high-res image (298KB)</a></li><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S2468025721000649-ga1.jpg">Download : Download full-size image</a></li></ol>

Improving on the Interparticle Connection for Performance Enhancement of Flexible Quantum Dot Sensitized Solar Cells

Improved Performance of Dye Sensitized Solar Cells Using Cu-doped TiO2 As Photoanode Materials: Band Edge Movement Study by Spectroelectrochemistry

Enhanced Current Density of Anatase TiO2 Nanowire Arrays by Interface Connection Modulation in Flexible Quantum Dot Sensitized Solar Cells

Flexible Quantum Dot-Sensitized Solar Cells with Improved Efficiencies Based on Woven Titanium Wires

Improvement in the photoelectric conversion efficiency for the flexible fibrous dye-sensitized solar cells

Preparation and Optimization of Flexible Quantum Dot Paste Based Photoanodes and Carbon Based Counter Electrodes

Titanium Mesh Based Fully Flexible Highly Efficient Quantum Dots Sensitized Solar Cells

Interface Connection Modulation by Heating Treatment for Photovoltaic Performance Enhancement on CuInS2 Quantum Dot Sensitized Solar Cells

Flexible and efficient perovskite quantum dot solar cells via hybrid interfacial architecture

The effect of dispersion of TiO 2 nanoparticles on preparation of flexible dye-sensitized photoanodes

High Performance PbS Quantum Dot Sensitized Solar Cells Via Electric Field Assisted in Situ Chemical Deposition on Modulated TiO2 Nanotube Arrays.

Large Pore Size and High Porosity of TiO2 Photoanode for Excellent Photovoltaic Performance of CdS Quantum Dot Sensitized Solar Cell.

Preparation and Properties of Flexible Dye-Sensitized Solar Cells

Optimization Of Tio2 Photoanode Films For Highly Efficient Quantum Dot-Sensitized Solar Cells

Titanium Dioxide (TiO2) Sensitized Zinc Oxide (ZnO)/Conducting Polymer Nanocomposites for Improving Performance of Hybrid Flexible Solar Cells

Improvement of performance of dye-sensitized solar cell by using composite nanoparticulate photoelectrode films

Dual Interfacial Modification Engineering with 2D MXene Quantum Dots and Copper Sulphide Nanocrystals Enabled High‐Performance Perovskite Solar Cells

Bifacial Illuminated PbS Quantum Dot-Sensitized Solar Cells with Translucent CuS Counter Electrodes

Significantly Enhanced Open Circuit Voltage and Fill Factor of Quantum Dot Sensitized Solar Cells by Linker Seeding Chemical Bath Deposition

Efficient quantum dot sensitized solar cells via improved loading amount management

Hydroxyl-Terminated CuInS2-Based Quantum Dots: Potential Cathode Interfacial Modifiers for Efficient Inverted Polymer Solar Cells.