Abstract:LNG floating production storage and offloading (FPSO) unit is a new type of floating production unit developed for offshore natural gas fields. It performs the functions of natural gas extraction, pretreatment, liquefaction, and storage. In this study, the heat transfer characteristics of a spiral-wound heat exchanger were studied using numerical simulations, which provides a basis for equipment selection and structural optimization of spiral-wound heat exchangers. The main research contents and conclusions are as follows. Under land-based simulation conditions, the heat transfer coefficient of the shell side of the spiral-wound heat exchanger decreases with an increase in the winding angle of the heat exchange tube, decreases with an increase in the spacing of the heat exchange tube, and increases with an increase in the outer diameter of the heat exchange tube. When the winding angle increased from 5° to 8°, the heat transfer coefficient decreased by 6.70%. The heat transfer coefficient of the shell side decreased by 13.21% when the heat exchange tube spacing increased from 14 to 17 mm. The heat transfer coefficient of the shell side increased by 22.89% when the outer diameter of the heat exchange tube increased from 9 to 12 mm. When the sloshing angle is constant, the heat transfer coefficient of the spiral-wound heat exchanger decreases with an increase in the winding angle and spacing of the heat exchange tubes, and increases with an increase in the outer diameter of the heat exchange tubes. When the structural parameters of the heat exchanger are constant, the heat transfer coefficient decreases as the sloshing angle increases. When the sloshing angle was less than 3°, the sloshing promoted heat transfer on the shell side. When the sloshing angle was higher than 7°, the heat transfer effect of the shell side deteriorated considerably, which weakened the heat transfer performance of the heat exchanger. When the sloshing period is constant, the heat transfer coefficient of the wound heat exchanger decreases with an increase in the winding angle and spacing of the heat exchange tubes, and increases with an increase in the outer diameter of the heat exchange tubes. When the structural parameters of the heat exchanger are constant, the heat transfer coefficient increases with sloshing period. When the sloshing period was greater than 15 s, the influence of sloshing on the heat transfer on the shell side of the heat exchanger was relatively weak.

Numerical Analysis Of The Energy Recovery Process In A Disc -Type Pressure Exchanger With Pressure-Boost Effect

Numerical Study on Hydrodynamics, Mixing and Heat Transfer of Highly Viscous Fluid in a Novel Shell-and-tube Heat Exchanger with X-type Baffles

Numerical Simulation of Mass and Heat Transfer in Detachable Spiral Heat Exchanger

Design and Optimization of A Large Flow Rate Booster Pump in Swro Energy Recovery System

Exergy Efficiency Design For Multi-Stream Plate-Fin Heat Exchangers Based On Entropy Generation Assessment

Numerical Simulation of Power Consumption and Mixing Characteristics of Novel Large-Double-blade Impeller

A numerical and experimental study of chevron, corrugated-plate heat exchangers

Numerical and experimental research on the integrated energy recovery and pressure boost device for seawater reverse osmosis desalination system

Numerical study on hydrodynamic characteristics of plate-fin heat exchanger using porous media approach

Influence of structural and operating factors on mixing transfer of rotary energy recovery device through CFD simulation

Performance Study of a Rotary Vane Pressure Exchanger for SWRO

A Parametric Study on the Effect of Mixing Chamber for Expansion Work Recovery CO2 Ejector

Numerical simulation for energy and exergy analysis of a novel turbulator in a heat recovery system filled with hybrid nanofluid

Numerical investigation and experimental validation of thermo-hydraulic and thermodynamic performances of helical baffle heat exchangers with different baffle configurations

Numerical Simulation on Enhanced Heat Transfer and Flow Characteristics in Direct-Contact Heat Exchanger: A Novel Kenics Static Mixer

Numerical Investigation on Three-fluid Heat Exchanger for Hybrid Energy Source Heat Pumps

Study on the operating characteristic of disc seal single screw pump used in energy recovery systems

Experimental Research on Energy Recovery Efficiency and the Leakage Characteristic of Rotary Pressure Exchanger

Study on the thermal performance of the cross-flow plate heat exchangers

Numerical simulation of heat transfer performance of spiral wound heat exchanger under sloshing condition

Multi-objective optimization and energy efficiency improvement for rotor duct in integrated energy recovery-pressure boost device