Abstract:High Performance Polymers, Ahead of Print. Modifying tribo films using filler particles is a significant area of research in developing polymer-based tribo components to minimize material loss during the sliding process. This study focused on altering the wear characteristics of a polyetheretherketone (PEEK)/graphene high-performance polymer composite to strengthen the tribo film by adding synthetic diamond particles. The hot-pressed PEEK composite reinforced by graphene and diamond particles increased the hardness and thermal stability of the composite. Compared with pure PEEK, composites containing 1% graphene and 1% diamond particles showed an increment of 25% and 23% in hardness and thermal stability, respectively. Fourier-transform infrared spectroscopy and X-ray diffraction analysis verified the compatibility and intactness of the fillers in the PEEK matrix. The tribo properties of PEEK composites were characterized by a pin-on-disc tribometer on a counter steel surface. A PEEK composite containing 0.75 wt% graphene and 0.5 wt% diamond particles exhibited the lowest friction of 0.17 at a pressure of 1.5 MPa. The specific wear rate was low (1.78 × 10−6 mm3/Nm) for the composite containing 1 wt% graphene and 1 wt% diamond particles at a pressure of 1.5 MPa. Varying synthetic diamond and graphene filler concentrations in the PEEK matrix change the wear process by modifying the tribo film characteristics, revealing the lowest friction and wear rate. X-ray photoelectron and Raman spectroscopy show that the polymer film was transferred to the steel countersurface, and the tribo-chemical products of the tribo film contribute to a stable tribo film. The ferric oxide film and the tribo film improve the composite's self-lubricating properties and load-bearing ability. Hence, the composite containing 0.75% of graphene and 0.5% of a synthetic diamond can be employed in the sliding bearing application of continuous conveyors used in mass production systems.

Tribological Behaviour of Polymeric Coatings: II. SCF‐Reinforced PEEK Nanocomposite Systems

Tribological behavior of modified polyetheretherketone composites in sliding against stainless steel under water lubrication

The Research of Polyetheretherketone Based Composite Coatings

A Comprehensive Review on the Tribological Evaluation of Polyether Ether Ketone Pristine and Composite Coatings

Tribological Behavior of Reinforced PTFE Composites and Un-Reinforced Polyketone-Based Materials against Coated Steel

Comparative Study of Friction and Wear Performance of PEK, PEEK and PEKK Binders in Tribological Coatings

Effect of Low-Friction Composite Polymer Coatings Fabricated by Electrophoretic Deposition and Heat Treatment on the Ti-6Al-4V Titanium Alloy’s Tribological Properties

Performance and mechanisms of different tribological thermoplastic composites in sliding contact with steel

Tribological Performance Study of Low-Friction PEEK Composites under Different Lubrication Conditions

Study on the Tribological Behaviors of Different PEEK Composite Coatings for Use As Artificial Cervical Disk Materials

Friction and wear performance of polyether ether ketone (PEEK) polymers in three lubrication regimes

Tribological and mechanical characterization of carbon-nanostructures based PEEK nanocomposites under extreme conditions for advanced bearings: A molecular dynamics study

The effects of filler type on the friction and wear performance of PEEK and PTFE composites under hybrid wear conditions

Tribological behavior of PEEK components with compositionally graded PEEK/PTFE surfaces

Tribological properties of PEEK-based composite coating prepared by thermal spraying

Tribological investigation into nickel-coated graphite polytetrafluoroethylene composites

Tribological performances of polymeric plain bearings made of epoxy matrix with UHMWPE, MoS2, Kevlar and base oil as the fillers

Tribological Properties of PEEK and Its Composite Material under Oil Lubrication

Tribological Properties of Polyether–Ether–Ketone-Based Coating under Mixed and Boundary Aviation Kerosene-Lubrication Condition

Tribological properties of PEEK composites reinforced by MoS2 modified carbon fiber and nano SiO2

Friction and wear characteristics of synthetic diamond and graphene-filled polyether ether ketone composites