Abstract:Modern computerized planning tools for periacetabular osteotomy (PAO) use either morphology-based or biomechanics-based methods. The latter relies on estimation of peak contact pressures and contact areas using either patient specific or constant thickness cartilage models. We performed a finite element analysis investigating the optimal reorientation of the acetabulum in PAO surgery based on simulated joint contact pressures and contact areas using patient specific cartilage model. Furthermore we investigated the influences of using patient specific cartilage model or constant thickness cartilage model on the biomechanical simulation results. Ten specimens with hip dysplasia were used in this study. Image data were available from CT arthrography studies. Bone models were reconstructed. Mesh models for the patient specific cartilage were defined and subsequently loaded under previously reported boundary and loading conditions. Peak contact pressures and contact areas were estimated in the original position. Afterwards we used a validated preoperative planning software to change the acetabular inclination by an increment of 5° and measured the lateral center edge angle (LCE) at each reorientation position. The position with the largest contact area and the lowest peak contact pressure was defined as the optimal position. In order to investigate the influence of using patient specific cartilage model or constant thickness cartilage model on the biomechanical simulation results, the same procedure was repeated with the same bone models but with a cartilage mesh of constant thickness. Comparison of the peak contact pressures and the contact areas between these two different cartilage models showed that good correlation between these two cartilage models for peak contact pressures (r = 0.634 ∈ [0.6, 0.8], p < 0.001) and contact areas (r = 0.872 > 0.8, p < 0.001). For both cartilage models, the largest contact areas and the lowest peak pressures were found at the same position. Our study is the first study comparing peak contact pressures and contact areas between patient specific and constant thickness cartilage models during PAO planning. Good correlation for these two models was detected. Computer assisted planning with FE modeling using constant thickness cartilage models might be a promising PAO planning tool when a conventional CT is available.

INFLUENCE OF MODELING METHODS FOR CARTILAGE LAYER ON SIMULATION OF PERIACETABULAR OSTEOTOMY USING FINITE ELEMENT CONTACT ANALYSIS

Evaluation of Constant Thickness Cartilage Models Vs. Patient Specific Cartilage Models for an Optimized Computer-Assisted Planning of Periacetabular Osteotomy

Biomechanical Optimization-Based Planning of Periacetabular Osteotomy.

Dynamic Assessment of Contact Pressure Changes in the Hip Joint Cartilage During Daily Activities.

Theoretical Implications of Periacetabular Osteotomy in Various Dysplastic Acetabular Cartilage Defects As Determined by Finite Element Analysis

Finite element modeling and mechanical analysis for Cam-type femoroacetabular impingement

Study on Simulation Modeling Method of the Reconstruction Following Resection of Peri-Acetabular Tumors

Motion Capture Based Dynamic Assessment of Hip Joint Cartilage Contact Pressure During Daily Activities.

Optimization Technique and Fe Simulation for Lag Screw Placement in Anterior Column of the Acetabulum

[Study on Finite Element Analysis Method for the Pre-operative Planning of Bernese Periacetabular Osteotomy].

Computer-Assisted Optimization of the Acetabular Rotation in Periacetabular Osteotomy Using Patient's Anatomy-Specific Finite Element Analysis

Finite Element Prediction of Contact Pressures in Cam-Type Femoroacetabular Impingement with Varied Alpha Angles

Contributions of non-spherical hip joint cartilage surface to hip joint contact stress.

Analysis of Finite Element Modeling on Elasto-Plasticity of Polyethylene Liner under Contact Stress after THA

Evaluation of the finite element software ABAQUS for biomechanical modelling of biphasic tissues

Porohyperelastic Finite Element Model for the Kangaroo Humeral Head Cartilage Based on Experimental Study and the Consolidation Theory

Sensitivity of knee cartilage biomechanics in finite element analysis to selected Musculoskeletal models

MODELING AND INJURY REPAIR ANALYSIS OF ARTICULAR CARTILAGE BASED ON FIBER CONTENT

In vivo finite element modeling and mechanical analysis of artificial hip joint

The influence of patellofemoral joint contact geometry on the modeling of three dimensional patellofemoral joint forces

Biomechanics of acetabular CE angle and direction of hip joint acting force