Abstract:The clarification of the critical operating conditions and the failure mechanism of superlubricity systems is of great significance for seeking appropriate applications in industry. In this work, the superlubricity region of 1,3-diketone oil EPND (1-(4-ethyl phenyl) nonane-1,3-dione) on steel surfaces was identified by performing a series of ball-on-disk rotation friction tests under various normal loads (3.5–64 N) and sliding velocities (100–600 mm/s). The result shows that beyond certain loads or velocities superlubricity failed to be reached due to the following negative effects: (1) Under low load (≤ 3.5 N), insufficient running-in could not ensure good asperity level conformity between the upper and lower surfaces; (2) the high load (≥ 64 N) produced excessive wear and big debris; (3) at low velocity (≤ 100 mm/s), the weak hydrodynamic effect and the generated debris deteriorated the lubrication performance; (4) at high velocity (≥ 500 mm/s), oil migration occurred and resulted in oil starvation. In order to expand the load and velocity boundaries of the superlubricity region, an optimized running-in method was proposed to avoid the above negative effects. By initially operating a running-in process under a suitable combination of load and velocity (e.g. 16 N and 300 mm/s) and then switching to the target certain higher or lower load/velocity (e.g. 100 N), the superlubricity region could break through its original boundaries. The result of this work suggests that oil-based superlubricity of 1,3-diketone is a promising solution to friction reduction under suitable operating conditions especially using a well-designed running-in strategy.

Anti-spreading behavior of 1,3-diketone lubricating oil on steel surfaces

Superlubricity of 1,3-Diketone Based on Autonomous Viscosity Control at Various Velocities

XPS and ToF-SIMS Analysis of the Tribochemical Absorbed Films on Steel Surfaces Lubricated with Diketone

Load and velocity boundaries of oil-based superlubricity using 1,3-diketone

Effect of the Molecular Structure of 1,3-Diketones on the Realization of Oil-Based Superlubricity on Steel/Steel Friction Pairs

Study on the Tribological Properties of Metal Rolling Bearing under Lubrication with Diketone Lubricants

Spreading Behavior of Single Oil Droplet Impacting Surface with/without a Thin Liquid Film

How to improve superlubricity performance of diketone at steel interface: Effects of oxygen gas

Combination of diketone and PAO to achieve macroscale oil-based superlubricity at relative high contact pressures

Synergistic Lubrication for Textured Surfaces Using Polar and Nonpolar Lubricants

Comparison of the Tribological Behavior of Steel–steel and Si3N4–steel Contacts in Lubricants with ZDDP or Ionic Liquid

Synergistic lubricating behaviors of graphene and MoS 2 dispersed in esterified bio-oil for steel/steel contact

The Synergistic Effects of Oil Additive Sulphurized Olefin with Chemico-Thermal Treatment Surfaces of Steel

Understanding the Lubrication Mechanism Between the Polyhydroxyl Group Lubricants and Metal Surfaces

Effect of lubricant additives on the tribological behavior of aluminum alloy against steel

Friction Reducing and Anti-Wear Property of Metallic Friction Pairs under Lubrication of Aqueous Solutions with Polyether Added

Industrial Gear Oils: Tribological Performance and Subsurface Changes

Influence of MoS2 and PTFE in Oil Film Characteristics and Tribological Performance in EHL Point Contacts

Study of Two Green Phosphonium‐based Ionic Liquids Lubricants for Steel/steel Contact

Simulation-based research on enhancing lubricity: investigating wettability and textured surfaces in alkane lubricants under boundary lubrication conditions

Tribological Study of Trioctylthiotriazine Derivative As Lubricating Oil Additive