Abstract:Two blends between polyamide 6 (PA6) and Polyamide 6co6T (PA6co6T, a random copolymer between polyamide 6 and polyamide 6T) were fabricated by melt-mixing on a twin-screw extruder and the subsequent injection molding, or through the in-situ polymerization of F-caprolactam in the presence of PA6co6T. As far as the former method is concerned, there exist an obvious decline of toughness and a slight increase in strength and modulus; however, for the latter, there appear a remarkable improvement in toughness and a simultaneous moderate increase in strength and modulus. A series of characterizations were carried out including scanning electron microscopy, wide-angle X-ray diffraction, polarized optical microscopy, differential scanning calorimetry, dynamic mechanical analysis, and Fourier transform infrared spectrometry. It is found that both blends exhibit single glass transition on DMA tan delta curves. However, contrary to that of the melt-mixed blends, the glass transition temperature (T-g) of the in-situ ones decreases with increasing PA6co6T content. It is suggested that different mixing levels are the main reasons. Moreover, the addition of PA6co6T containing linear rigid segments conducts remarkable refinement of spherulites for the blends. Significantly different changes in the crystallographic form, spherulite size, crystalline content and perfection due to the introduction of PA6co6T for the two blends are ascribed to their varied thermomechanical histories and the presence of interchange reaction only for the in-situ blends. On the basis of the characterizations of the microstructures, the different trends of changes in the mechanical properties with the addition of PA6co6T for the two fabrication methods are discussed. (C) 2007 Wiley Periodicals, Inc.

Improved thermal properties by controlling selective distribution of AlN and MWCNT in immiscible polycarbonate (PC)/Polyamide 66 (PA66) composites

Effect of hybrid nanofillers on thermal conductivity of composite phase change materials

Improved Thermal Conductivity of Ceramic Filler‐filled Polyamide Composites by Using PA6/PA66 1:1 Blend As Matrix

Mutual Nucleating and Crystallization Behavior of Poly (ethylene Terephthalate)/polyamide 66 Blends

Enhancing flame retardancy and heat insulation performances of polyamide 66 composite film by adding CNC/Al2O3 nanohybrids

Enhanced Thermal Conductivity and Microwave Dielectric Properties by Mesostructural Design of Multiphase Nanocomposite

Additive Manufacturing of Polyamide 66: Effect of Process Parameters on Crystallinity and Mechanical Properties

In-situ Compatible Composite of Nylon 66 and Thermotropic Liquid Crystalline Polyamide

Study on Thermal Conducting Insulating Polycarbonate and Polycarbonate/abs Polymers

Enhanced Thermal Conductivity of Polypropylene/polyamide 6 Composites Via Optimizing the Selective Distribution of H-Bn and NH2-CNTs Hybrid Fillers Within the Co-Continuous Structure

Improved thermal conductivity of polycarbonate composites filled with hybrid exfoliated graphite/multi-walled carbon nanotube fillers

Enhanced Thermal Conductivity in Polyamide 6 Composites Based on the Compatibilization Effect of Polyether-Grafted Graphene

Study on Thermotropic Liquid Crystalline Copolyamide/Polyamide 66 In situ Composites

Crystallization Behavior and Mechanical Properties of Polyamide 66/thermotropic Liquid Crystalline Copolyamide Blends

Conductive polycarbonate composites prepared by a ternary polymer blend approach involving sea‐island‐type interfacial carbon black networks

A double mixing process to greatly enhance thermal conductivity of graphene filled polyamide 6 composites

Improving Thermal Conductivity of Injection Molded Polycarbonate/Boron Nitride Composites by Incorporating Spherical Alumina Particles: The Influence of Alumina Particle Size

Hybrid of multi‐dimensional fillers for thermally enhanced polyamide 12 composites fabricated by selective laser sintering

Influence of Preparation Methods on the Structures and Properties for the Blends Between Polyamide 6co6t and Polyamide 6: Melt‐mixing and In‐situ Blending

Polymer Composite with Enhanced Thermal Conductivity and Insulation Properties through Aligned Al2O3 Fiber

Thermal Deformation of PA66/Carbon Powder Composite Made with Fused Deposition Modeling