Abstract:This study investigates the flow characteristics and unsteady heat transfer of noncircular synthetic jets impinging on a heated plate. Thermographic phosphor thermometry and time-resolved particle image velocimetry are used to acquire quantitative wall temperature and flow field information, respectively. At a constant orifice-to-wall distance (H/De = 7.5), five orifice configurations (circular, square, elliptic with aspect ratio (AR) of 3, and rectangular with ARs of 3 and 5) are examined at a wall temperature of 80 °C. The orifice configuration has a significant effect on the heat transfer and vortex behavior of the impinging synthetic jets. The square orifice displays better stagnation cooling performance with 42% increase in the maximum stagnation cooling coefficient relative to the circular case due to the larger impinging velocity and deeper penetration into the wall shear layer. Axis-switching of the vortex rings is detected for both the elliptic and rectangular orifices before they impinge onto the wall. The axis-switching enhances the near-wall mixing and turbulent kinetic energy in the elliptic and rectangular orifices, and thus heat transfer compared with the circular case. Additionally, stronger vortices and deeper penetration into the wall shear layer are observed in the major-axis plane than in the minor-axis plane, leading to enhanced heat transfer in the major-axis direction. In particular, the rectangular orifice with an AR of 5 induces strong secondary structures in the trailing jet following the primary vortex ring, and these are responsible for the double-peak distribution of wall temperature in the major-axis direction. This is the first time a double-peak temperature distribution has been reported for noncircular impinging synthetic jets. The rectangular orifice with an AR of 5 also yields a larger cross-stream velocity in the minor-axis direction, indicating a stronger wall jet. Thus, among the cases considered in this study, the rectangular orifice with AR = 5 achieves the optimal cooling performance and the maximum time-averaged cooling area reaches more than 14 times the jet orifice area.

Effects Of Different Orifice Structure On Heat Transfer Characteristics Of Steel Strip Surface In An Air Impinging Freezer

Effect of Inclined Orifice in Air Impingement Freezer on Heat Transfer Characteristics of Steel Strip Surface

Numerical simulation and experimental study of strip steel jet cooling

Experimental study on the frosting and heat transfer characteristics of cooling surfaces in confined parallel and counter flow channels

Effect Of Corrugated Orifice And Pin-Fin On Multiple Array Impingement Cooling With Low Nozzle To Target Distance

Experimental Study on the Frosting Characteristics of Round Tube in Confined Circular Flow Path at Low Temperature

Experimental And Numerical Investigation Of Transpiration Cooling For Sintered Porous Flat Plates

Numerical investigation on the impact of injection rates on cooling performance in a rotor-stator cavity with liquid nitrogen spraying

An experimental study on the dynamic frosting characteristics on the edge zone of a horizontal copper plate under forced convection

Effect of the Nozzle Geometry on Flow Field and Heat Transfer in Annular Jet Impingement

Effect of compact fin structure on heat transfer performance of ice storage unit during freezing

Study of Heat Transfer Coefficients of Multiple High-Pressure Fan-Shaped Water Impinging on the Lower Surface of High-Temperature Steel Billets

Experimental investigation on flow characteristics and unsteady heat transfer of noncircular impinging synthetic jets

Influence of Dimension Effect on Convective Beat Transfer in Micro/mini-Cylinders-group at Low Reynolds Number

Air Distribution Optimization Of Impingement Freezer

Research on Injected Effect and Heat-Transfer Characteristics of Narrow-Slit Injection Orifice Used for the Screw Compressor.

An Experimental Study on the Effect of Horizontal Cold Plate Surface Temperature on Frosting Characteristics under Natural Convection

The effect of laminar cooling heat transfer coefficient on the temperature field of steel plate

Experimental study on heat transfer characteristics of flowing air on the surface of finned-tube vaporizer under frosting conditions

Experimental Heat Transfer and Cooling Effectiveness over an Effusion Wall with Internal Jet-Array Impingement: Influence of Hole Arrangement

Experimental investigation of metal foam embedded surface thermal characteristics using air-jet impingement with different orifice geometry