Abstract:The flow condensation heat transfer coefficient of R134a inside two helical micro-fin tubes with outer diameter of 6.35 mm and helical angles of 18o and 28o respectively were experimentally studied at a high mass flux ranging from 500 to 1100 kg m−2 s−1. The condensation temperatures are 35°C, 40°C and 45°C, and the vapor qualities ranges from 0.95 to 1.00 at the inlet section and from 0.00 to 0.05 at the outlet section. Experimental results show that there are annular and intermittent flow regimes inside the tube under experimental conditions, the ratio of annular flow region to the total heat transfer region is about 70%. The liquid film flow changes from rotational flow to coexistence of rotational and horizontal flows when the vapor quality is 0.475±0.08, 0.486±0.06 and 0.521±0.05, respectively and the corresponding saturation temperature is 35°C, 40°C and 45°C. Based on the experimental data, the heat transfer coefficient increases with increasing mass flux and fin helical angle, and with decreasing saturation temperature and Reynolds number of cooling water. In addition, the heat transfer coefficient of annular flow is greater than that of intermittent flow, in other words, the heat transfer coefficient increases with increasing vapor quality. The heat transfer coefficient obtained at high mass flux was compared with the calculated data of some published correlations used at low mass flux. It was found that most correlations underestimate the experimental heat transfer coefficient inside the micro-fin tube, and these prediction deviation increases with increasing mass flux and fin helical angle. By introducing some dimensionless numbers as well as considering the flow mechanism of liquid film inside the tube, two heat transfer coefficient correlations were proposed based on the experimental data. The ratio of liquid film thickness to fin height was used to characterize whether the liquid film flow is rotational flow or coexistence of rotational and horizontal flows in the proposed correlation, which shows a better prediction accuracy with a mean deviation of less than 7.3%.

Influence of Dimension Effect on Convective Beat Transfer in Micro/mini-Cylinders-group at Low Reynolds Number

Flow and Heat Transfer Characteristics in a Microchannel with a Circular Synthetic Jet

Detailed Heat Transfer Measurements of Curved Fin Channels

Fluid Flow and Heat Transfer Performance in a Micro-Reactor with Non-Uniform Micro-Pin-fin Arrays for Hydrogen Production at Low Reynolds Number

Heat and mass transfer characteristics in reforming micro-reactor with micro-pin-fin arrays

Experimental Study of Condensation Heat Transfer of R134a Inside the Micro-Fin Tubes at High Mass Flux

Effects of Geometrical Parameters on Heat Transfer Enhancement in V-Spirally Corrugated Tube

HEAT TRANSFER CHARACTERISTICS OF WATER FLOWING THROUGH MICROCHANNELS

Convective Heat Transfer Coefficient for a Rod-Like Particle in a Uniform Flow

Local Vorticity and Flow Heat Transfer Mechanism Analysis in Micro-Cylinder-Groups Based on Field Synergy Principle

A study on flow and heat transfer characteristics of manifold microchannels based on lattice Boltzmann method

Study on the efficient heat transfer mechanism of microchannel pin-fin arrays under low pumping power

Experimental and numerical study of mixed convection heat transfer in a vented cavity partially filled with a porous medium: Effects of reynolds and rayleigh numbers on Nusselt number and flow regimes

The Effect on the Nusselt Number of the Nonlinear Axial Temperature Distribution of Gas Flows Through Microtubes

Numerical Simulation of Heat Transfer and Pressure Drop Characteristics of Internal Microfin Tubes

Numerical investigation on the effect of cylindrical turbulator on performance of corrugated plate-fin heat exchanger

Analysis of Local Heat Transfer Characteristics of Water and Steam in Helically-Coiled Tube

Effect of Thermal Boundary Conditions and Thermal Conductivity on Conjugate Heat Transfer Performance in Pin Fin Arrays

Simultaneously developing flow and heat transfer in circular and parallel-plates microchannels with velocity slip and temperature jump

Using Direct Simulation Monte Carlo with Improved Boundary Conditions for Heat and Mass Transfer in Microchannels

Numerically Investigated Effects of Different Dean Number and Pitch Size on Flow and Heat Transfer Characteristics in a Helically Coil-Tube Heat Exchanger