Abstract:Thermal management of high-heat-flux electronics has been a critical bottleneck for integrated circuit miniaturization and increased power density, and manifold microchannel (MMC) heat sinks are expected to be an efficient near-junction thermal solution. A numerical investigation based a self-developed solver has been conducted to explore the effects of manifold geometries on the thermal–hydraulic performance of MMC heat sinks during subcooled flow boiling, and phase, pressure, and mass distribution among microchannels are analyzed combined with temperature distribution. Heat flux makes little difference on the mass maldistribution among microchannels of MMCs regardless of single-phase and flow boiling, and flow patterns in the outlet manifolds of Z-type MMCs changes from bubbly flow, slug flow to vapor columns with segmented bubbles with increasing heat fluxes. As for the effect of manifold numbers, both the maximum temperature and the pressure drop decrease with increasing manifold numbers, and a relatively uniform distribution of mass and void fraction has been found for all cases of HU-type MMCs regardless of heat fluxes with the best thermal–hydraulic performance at N = 10. However, the thermal performance of Z-type MMCs would improve firstly and then flatten out with increasing manifold number, while the pressure drop presents an opposite trend. The differences in thermal–hydraulic performance are attributed to the longer flow path in Z-type manifolds, and the increasing manifold number presents a higher manifold pressure drop and thus would worsen the mass maldistribution. As for tapered manifolds, a tapered ratio of 0.33 could provide a slightly lower base temperature than the original case with a pressure drop decreased by over 25 %, and the pressure drop fluctuation at high heat fluxes could be suppressed by 70 % with significantly improved flow boiling stability. This work can serve as a basis for the further optimization of subcooled flow boiling in MMC heat sinks, and the results indicate that both an even mass distribution among microchannels and a desirable inlet/outlet port ratio for improved flow field are of great importance for the manifold design applied in MMC heat sinks for two-phase heat dissipation.

A study on flow and heat transfer characteristics of manifold microchannels based on lattice Boltzmann method

Detailed Heat Transfer Measurements of Curved Fin Channels

A Numerical Study of Subcooled Flow Boiling in a Manifold Microchannel Heat Sink with Varying Inlet-to-outlet Width Ratio

Heat and mass transfer characteristics in reforming micro-reactor with micro-pin-fin arrays

Numerical investigation of heat transfer and pressure drop characteristics of flow boiling in manifold microchannels with a simple multiphase model

A Comparative Numerical Study on Two-Phase Boiling Fluid Flow and Heat Transfer in the Microchannel Heat Sink with Different Manifold Arrangements

Numerical investigation of novel manifold microchannel heat sinks with countercurrent regions

Discussion on heat transfer correlation in turbulent channel flow imposed wall-normal magnetic field

Numerical Investigation Of Flow Boiling In A Manifold Microchannel Heat Sink With Conjugate Heat Transfer

Single-phase and Two-phase Flow and Heat Transfer in Microchannel Heat Sink with Various Manifold Arrangements

A numerical investigation of the thermal–hydraulic performance during subcooled flow boiling in MMCs with different manifolds

Heat Transfer and Flow Characteristics of Flow Boiling in Manifold Microchannel

Flow Manifold Optimization for a Uniform Velocity Distribution in a Laminated Microreactor with Micro‐Pin‐Fin Arrays

HEAT TRANSFER CHARACTERISTICS OF WATER FLOWING THROUGH MICROCHANNELS

Analysis of Thermal Performance and Pressure Loss of Subcooled Flow Boiling in Manifold Microchannel Heat Sink

Lattice-Boltzmann Method for Gas Flow in Microchannels

Thermal and hydrodynamic characteristics of single-phase flow in manifold microchannels with countercurrent regions

Flow thermohydraulic characterization of hierarchical-manifold microchannel heat sink with uniform flow distribution

Numerical Study on Flow and Heat Transfer of a Hybrid Microchannel Cooling Scheme Using Manifold Arrangement and Secondary Channels

Study on the efficient heat transfer mechanism of microchannel pin-fin arrays under low pumping power

Study on the flow and heat transfer characteristics of pin-fin manifold microchannel heat sink