Abstract:Fly ash (FA) contents and water-binder ratio ( w / b ) are the important factors influencing the mechanical characteristics of cement-based materials, meanwhile the porous structure of material plays a vital role. The compressive strength and water permeability of cement-based samples with high-volume FA contents (0%, 30%, 40%) and different w / b (0.3, 0.4, 0.5) were measured. The results demonstrated that higher FA contents or greater w / b led to lower compressive strength and higher water permeability at an early stage. The pore structure features of samples were obtained using mercury intrusion porosimetry and low-temperature nitrogen gas adsorption (LT-NGA). The pore size distributions (PSDs) and the matrix compressibility in cementitious materials were also analyzed, with the compression coefficient K C ranging from 11.919 to 1.249 × 10 −4 MPa −1 . Increasing the FA content and reducing the w / b resulted in an optimized pore structure of the samples, characterized by changing the main pore type from mesopores (10–50 nm) to micropores (< 10 nm). The pores and fractures in the samples also had distinct multifractal characteristics. The strongest negative correlation between the compressive strength and the width of the multifractal generalized spectrum was proved by Pearson correlation analysis, and the correlation coefficient ( ρ ) was − 0.93. Furthermore, the water permeability had the strongest positive correlation with porosity, with ρ of 0.91. The content of macropores (50–10 μm) had greater influence on its macroscopic properties. The dense structure accompanied by homogeneous PSDs is advantageous for enhancing the strength and anti-permeability properties of cement-based materials.

The Pore Fillability of Cementitious Materials and Its Application in Predicting Compressive Strength of Gap-Graded Blended Cements

A new method for predicting compressive strength of cement-based materials

Is Early Drying Shrinkage Still Determined by the Mesopore Content? A Case Study of Cement Paste with Minerals

Volumetric Deformation of Gap-Graded Blended Cement Pastes with Large Amount of Supplementary Cementitious Materials

Micro-structural Development of Gap-Graded Blended Cement Pastes Containing a High Amount of Supplementary Cementitious Materials

A Gap-Graded Particle Size Distribution for Blended Cements: Analytical Approach and Experimental Validation

Empirical Estimation of Pore Size Distribution in Cement, Mortar, and Concrete

Study of the Relationship between the Strength of the hydrated Cement Paste with Flyash and its Pore structure

Analysis of Pore Structures and Their Relations with Strength of Hardened Cement Paste

A new gap-graded particle size distribution and resulting consequences on properties of blended cement

Segmented Fractal Pore Structure in Cement-Based Materials Blended with Dolomite Powder

Simple Three-Step Analytical Scheme for Prediction of Elastic Moduli of Hardened Cement Paste

Strength, Permeability and Multiscale Pore Characteristics of Cement-Based Materials with High-Volume Fly Ash Contents and Different Water-Binder Ratios

Influence of Preparation Method on the Performance of Ternary Blended Cements

Effects of Water-to-Cement Ratio on Pore Structure Evolution and Strength Development of Cement Slurry Based on HYMOSTRUC3D and Micro-CT

A Study on the Relationship Between Porosity of the Cement Paste with Mineral Additives and Compressive Strength of Mortar Based on This Paste

Improved Predictions of Permeability Properties in Cement-Based Materials: A Comparative Study of Pore Size Distribution-Based Models

Analysis of Correlation Between Hydration Heat Release and Compressive Strength for Blended Cement Pastes

Influence of Porosity on Compressive and Tensile Strength of Cement Mortar

Study on the Strength and Micro Characteristics of Grouted Specimens with Different Superfine Cement Contents

Evaluation of Inherent Factors on Flowability, Cohesiveness and Strength of Cementitious Mortar in Presence of Zeolite Powder