Abstract:In this work, resin‐derived carbon coating was prepared on carbon fibers by polymer impregnation pyrolysis method, then silicoboron carbonitride powder was prepared by mechanical alloying, and finally carbon fiber‐reinforced silicoboron carbonitride composites were prepared by hot‐pressing process. The effects of sintering densification and fiber coating on microstructure, mechanical properties, thermal shock resistance, and failure mechanisms of the composites were studied. Fiber bridging hinders the sintering densification, causing more defects in fiber‐dense area and lower strength. However, higher sintering temperature (1800–2000°C) can improve mechanical properties significantly, including bending strength, vickers hardness, and elastic module, because further sintering densification enhances matrix strength and fiber/matrix bonding strength, while the change of fracture toughness is not obvious (2.24–2.38 MPa·m1/2) due to counteraction of higher debonding resistance and less pull‐out length. However, fiber coating improves fracture toughness greatly via protecting carbon fibers from chemical corrosion and damage of thermal stress and external stress. Due to lower coefficient of thermal expansion, lower fiber loading ratio, less stress concentration at the fiber/matrix interface, and better defect healing effect, lower sintering temperature favors thermal shock resistance of composites, and thermal shock recession mechanisms are the damage of interface.

Improved Thermal Shock Resistance of SiCnw/PyC Core-Shell Structure Toughened CVD-SiC Coating

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Improved oxidation and thermal shock resistance of SiC-Si coating with a SiC w /PyC network structure toughened buffer layer

Effects of HfC/PyC Core-Shell Structure Nanowires on the Microstructure and Mechanical Properties of Hf1-xZrxC Coating

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Fabrication of porous SiC nanostructured coatings on C/C composite by laser chemical vapor deposition for improving the thermal shock resistance

Effect of the Incorporation of SiC Nanowire with Double Protective Layers on SiC Coating for C/C Composites

Low residual stress SiC coatings on C/CA composites by a strategy of matching their expansion behaviors to improve thermal shock resistance

Interfacial modification and oxidation resistance behavior of a CVD-SiC coating for C/SiC composites

Effect of SiCnws@BN core shell upon impact-ablation performance of HfC coating on C/C composites

Siliconization elimination for SiC coated C/C composites by a pyrolytic carbon coating and the consequent improvement of the mechanical property and oxidation resistances

Improved antioxidative and mechanical properties of SiC coated C/C composites via a SiO2-SiC reticulated layer

Thermal shock behavior and oxidation resistance of novel SiC nanowires+Si/Yb2Si2O7-Si/Yb2Si2O7 environmental barrier coatings

Effect of PyC-SiC double-layer interface on ablation behaviour of impacted CVD-SiCnws/HfC coating

Microstructure and ablation performance of HfC/PyC core-shell structure nanowire-reinforced Hf1-xZrxC coating

Oxidation resistance behavior of SiC nanowires/Si layer on the C/SiC composites

Mechanical and thermal shock properties of C f /SiBCN composite: Effect of sintering densification and fiber coating

The toughening design of multi-layer antioxidation coating on C/C matrix via SiC-SiCw transition layer grown in-situ

Enhanced thermal and mechanical properties of optimized S i C f / S i C composites with in-situ CNTs on PyC interface

In-situ SiC nanowires reinforced SiC-based multicomponent ceramic coating for protecting SiOC/CF composites

Effects of SiO 2 -coated CNTs on the directional formation of SiC whiskers and improvement in the ablative resistance of polymer-matrix composites