Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

Design of a Water-Cooled Tube for High-Power and Long-Pulse Radio Frequency Ion Source

Engineering design and manufacturing of a radio frequency plasma driver without Faraday shield for NBI application

Progress of High Heat Flux Component Manufacture and Heat Load Experiments in China

Plasma discharge experiments of a Faraday shieldless driver for high-power and long-pulse radio frequency ion source for NBI application

Turbulent Heat Transfer for Coolant Water Flow in Plasma Facing Component

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Development of megawatt radiofrequency ion source for the neutral beam injector on HL-2A tokamak

PISCES-RF: a liquid-cooled high-power steady-state helicon plasma device

Cooling Circuit Development of Equatorial Diagnostic Port Plug Dedicated to International Thermonuclear Experimental Reactor

Structure design and analysis of RF ion source for negative ion source test facility

Achievement of 1000 S Plasma Generation of RF Source for Neutral Beam Injector

R&D on High-Power Dc Reactor Prototype for ITER Poloidal Field Converter

Progress in the Engineering Design of Iter Langmuir Probe

Research and development progress of radio frequency ion source for neutral beam injector at ASIPP

Ion heating in the PISCES-RF liquid-cooled high-power, steady-state, helicon plasma device

Modeling inductive radio frequency coupling in powerful negative hydrogen ion sources: optimizing the RF coupling

Development and preliminary results of radio frequency ion source

Three-dimensional Modeling of the Large and Powerful Radio Frequency Negative Hydrogen Ion Source with Faraday Shield

Compact, inexpensive target design for steady‐state heat removal in high‐heat‐flux fusion applications

Thermal Design of High-Power DC Reactor for ITER Poloidal Field Converter

Simulation study on the discharge of radio frequency ion source for EAST neutral beam injector