Abstract:Hybrid high-power impulse and dc magnetron co-sputtering (HiPIMS/DCMS) with substrate bias synchronized to the high mass metal-ion fluxes was previously proposed as a solution to reduce energy consumption during physical vapor deposition processing and enable coatings on temperature-sensitive substrates. In this approach, no substrate heating is used (substrate temperature is lower than 150 o C) and the thermally activated adatom mobility, necessary to grow dense films, is substituted by overlapping collision cascades induced by heavy ion bombardment and consisting predominantly of low-energy recoils. Here, we present direct evidence for the crucial role of W + ion irradiation in the densification of Ti 0.31 Al 0.60 W 0.09 N films grown by the hybrid W-HiPIMS/TiAl-DCMS co-sputtering. The peak target current density J max on the W target is varied from 0.06 to 0.78 A/cm 2 resulting in more than fivefold increase in the number of W + ions per deposited metal atom, η = W + /(W + Al + Ti) determined by time-resolved ion mass spectrometry analyses performed at the substrate plane under conditions identical to those during film growth. The DCMS is adjusted appropriately to maintain the W content in the films constant at Ti 0.31 Al 0.60 W 0.09 N. The degree of porosity, assessed qualitatively from cross-sectional SEM images and quantitatively from oxygen concentration profiles as well as nanoindentation hardness, is a strong function of η(Jmax) . Layers grown with low η values are porous and soft, while those deposited under conditions of high η are dense and hard. Nanoindentation hardness of Ti 0.31 Al 0.60 W 0.09 N films with the highest density is ∼33 GPa, which is very similar to values reported for layers deposited at much higher temperatures (420–500 o C) by conventional metal-ion-based techniques. These results prove that the hybrid HiPIMS/DCMS co-sputtering with bias pulses synchronized to high mass metal ion irradiation can be successfully used to replace conventional solutions. The large energy losses associated with heating of the entire vacuum chamber are avoided, by focusing the energy input to where it is in fact needed, i.e., the workpiece to be coated.

Highly Conductive Ultrathin Co Films by High-Power Impulse Magnetron Sputtering

In-plane Isotropic High-Frequency Soft Magnetic Co-SiO2 Films

Co-based Nanogranular Thin Films on Flexible Substrate for Gigahertz Applications

Deposition of Dense SiO2 Thin Films for Electrical Insulation Applications by Microwave ECR Plasma Source Enhanced RF Reactive Magnetron Sputtering

Ultrahigh frequency properties of discontinuous CoFeB/SiO_2 multilayer films with high resistivity

Structure, mechanical and tribological properties, and oxidation resistance of TaC/a-C:H films deposited by high power impulse magnetron sputtering

Enhanced Electrical Properties of Copper Nitride Films Deposited via High Power Impulse Magnetron Sputtering

Influence of HiPIMS Pulse Widths on the Structure and Properties of Copper Films

The Effect of Co Content and Annealing Temperatures on the Resistivity in Ag-Co Films

Metal Filling by High Power Impulse Magnetron Sputtering

Superiority of High Power Impulse Magnetron Sputtering in Niobium Films Deposition on Copper

Multi-pulse electrodeposition of soft magnetic thin film Co-P for embedded inductor application

Effect of Sputtering Input Powers on Cosi2 Thin Films Prepared by Magnetron Sputtering

Cr/SmCo/Cu/Cr thin films with high coercivity deposited at low pressure

Plasma-Enhanced Atomic Layer Deposition of Cobalt Films Using Co(EtCp)2 As a Metal Precursor.

Thickness dependence of structural and magnetic properties of electrodeposited Co 2 FeSn films

Determining role of W+ ions in the densification of TiAlWN thin films grown by hybrid HiPIMS/DCMS technique with no external heating

Properties and Structure of High Coercivity Sm(Co, Al, Si)/Cr Sputtered Thin Films

Effect of Si contents on microstructure and mechanical characteristics of TiAlSiN thin film deposited by HiPIMS using different Ti Si target compositions

Structural, magnetic and transport properties of thin films of the Heusler alloy Co2MnSi

Low-density HiPIMS favored ultrathick and compact chromium coatings on Zircaloy-4 alloys