Abstract:This study aims to develop a refractive-index sensor operating in the visible region using an all-dielectric metasurface, which was chosen for its advantages of low optical loss and narrow spectral bandwidth, compared to those of conventional metallic metasurfaces. COMSOL software was utilized as a calculation tool to simulate the resonant properties of an all-dielectric metasurface composed of a circular nanohole-structured titanium oxide (TiO2) thin film, with the aim of enhancing the sensitivity of the refractive index for sensing targets. The simulation focused on finding the best geometrical conditions for the all-dielectric metasurface to achieve high sensitivity. Two resonance modes observed in this metasurface were considered: the quasi-bound-state-in-the-continuum (qBIC) mode and the perfect-reflection (PR) mode. The simulated results demonstrated that high sensitivities of 257 nm/RIU at the PR mode and 94 nm/RIU at the qBIC mode in the visible spectral range could be obtained by periodically constructing the metasurface with a unit cell having a lattice constant of 350 nm, a nanohole radius of 160 nm, and a nanohole depth of 250 nm. Furthermore, the study showed that the resonance mode that enabled high sensitivity was the PR mode, with a sensitivity nearly three times larger than that of the qBIC mode and the ability to reach the highest reflectance at the resonance wavelength. The optimized feature had the highest reflectance at a resonant wavelength of 570.19 nm, and although the quality factor was 25.50, these designed parameters were considered sufficient for developing a refractive index biosensor with high sensitivity and optical efficiency when operating in the visible spectral range.

Refractive Index Sensing Using All-Dielectric Metasurface with Analogue of Electromagnetically Induced Transparency

All-Dielectric Metasurface Refractive Index Sensor with Microfluidics

All-dielectric Metasurface with Multiple Fano Resonances Supporting High-Performance Refractive Index Sensing

Simultaneous Measurement of Refractive Index and Temperature Based on All-Dielectric Metasurface.

An all-dielectric metasurface based on Fano resonance with tunable dual-peak insensitive polarization for high-performance refractive index sensing

High-Performance Refractive Index and Temperature Sensing Based on Toroidal Dipole in All-Dielectric Metasurface

Design of the Refractive Index Sensor Based on EIT-Like Phenomenon

All-Dielectric Metasurface Based on Complementary Split-Ring Resonators for Refractive Index Sensing

Electromagnetically Induced Transparency in Planar Complementary Metamaterial for Refractive Index Sensing Applications

Optimization of the Geometrical Design for an All-Dielectric Metasurface Sensor with a High Refractive-Index Response

Refractive index sensor based on bound states in the continuum in silicon-based metasurface

All-Dielectric Metasurface Refractive Index Sensor with High Figure of Merit Based on Quasi-Bound States in the Continuum

Toroidal Dipole All-Dielectric Metasurfaces with High Sensitivity, High Figure of Merit, and Robustness for Refractive Index Sensing

Dual High-Q Resonance Sensing for Refractive Index and Temperature Based on All-Dielectric Asymmetric Metasurface

Staggered H-shaped Metamaterial Based on Electromagnetically Induced Transparency Effect and Its Refractive Index Sensing Performance

High Q-factor Fano Resonances Driven by Quasi Bound State in the Continuum Based on All-Dielectric Metasurface

Refractive Index Sensing Utilizing Tunable Polarization Conversion Efficiency with Dielectric Metasurface

High-Sensitivity Sensing in All-Dielectric Metasurface Driven by Quasi-Bound States in the Continuum

Quasi-BIC based all-dielectric metasurfaces for ultra-sensitive refractive index and temperature sensing

High Sensitivity Refractive Index Sensor Based on Metamaterial Absorber

Performance analysis and optimization of high Q-factor toroidal resonance refractive index sensor based on all-dielectric metasurface