Abstract:Spheroidized ferrite-cementite steel (SFC) is susceptible to micro-defects owing to the mismatched deformation between the ferrite and cementite during cold forming, which seriously deteriorates the fatigue life. However, the damage mechanism related to microstructural features in the SFC steel during cold deformation has not been fully investigated, hindering control of the microstructure and forming process. This study presents a method coupled with experiments and multiscale simulations to research the damage mechanisms and the dependence of microstructure features under uniaxial tension in SFC steel. In situ tensile test revealed three damage mechanisms in SFC steel under uniaxial tension: cementite cracking, ferrite/cementite interface debonding, and ferrite cracking. In particular, the final fracture was mainly dominated by the ferrite/cementite interface debonding. In multiscale simulations, the macroscale tensile and nanoindentation simulations were carried out to obtain the strain history and mechanical properties of the mesoscale simulations, respectively. The mesoscale IP-based RVE and CP-based unit cells simulations were performed to capture the driving forces from the three damage mechanisms and the dependence of microstructural features, respectively. The nanoscale molecular dynamics simulation was conducted to identify the model parameters of cohesive zone model (CZM) in the mesoscale simulations. The numerical results indicated that particle-cracking void occurred when the internal von Mises stress exceeded the ultimate strength of the cementite particles. Interface-debonding void nucleated when the load on the particle was insufficient to resist its strength. Matrix-cracking should be attributed to the stress concentration caused by the dislocation pile-up or the crossing of multiple slip bands. In addition, interfacial debonding were more likely to occur in the stable orientations and high-angle grain boundaries of ferrite matrix. Compared with a circular cementite particle, an elliptical particle was more prone to cause interfacial debonding. Also, the ferrite/ferrite grain boundary showed earlier interfacial debonding perpendicular to the loading direction than parallel to the loading direction.

Real Microstructure-Based Simulation of Thermal Residual Stresses in Cemented Carbides and the Related Strengthening and Toughening Consideration

The influence of the WC-Co composite microstructure model on stress field heterogeneity at the microstructure level: FEM based study

Design for Manufacturing of Cemented Carbide Coated Components Toward High Wear and Impact Resistance Performance

Influence of particulate B4C with high weight fraction on microstructure and mechanical behavior of an Al-based metal matrix composite

Coupling Residual Stress Field to Enhance the Simulation Accuracy of Crack Propagation and Mechanical Responses of High Entropy Ceramics Reinforced by Graphene and Alumina

Numerical modeling and failure evolution of microstructure-based in-situ TiB2 and TiC+TiB2 reinforced Cu matrix composites

Role of the microstructure and the residual strains on the mechanical properties of cast tungsten carbide produced by different methods

Investigation of damage mechanisms related to microstructural features of ferrite-cementite steels via experiments and multiscale simulations

Micromechanical Analysis of SiC/Ti6Al4V Composite Under Complex Stress State

Microstructural evolution and performance analysis of WC-11Co reinforced iron matrix composites

Residual stresses in ultrasonic vibration assistance turning cemented carbide

Developing Cemented Carbides Through ICME

Numerical investigations on the hybrid effect and deformation mechanism of TiB2p and TiBw reinforced Cu composites prepared by in-situ mixing casting

Stochastic Simulation of Thermal Residual Stress in Environmental Barrier Coated 2.5D Woven Ceramic Matrix Composites

Investigating the effect of WC reinforcements in Cu Ti composite filler on the microstructural evolution and mechanical characteristics in brazing C f /SiC and GH3536

Microstructure Evolution in the Cemented Carbides Wc-Coi. Effect of the C/W Ratio on the Morphology and Defects of the Wc Grains

Mechanism for magnetic field induced structural relaxation and accompanying fracture toughness improvement of the thermal spraying coating

Microstructural based constitutive modeling and subsurface microhardness prediction in machining of network-structured TiBw/TA15 composites

Investigating the Effect of Cementite Particle Size and Distribution on Local Stress and Strain Evolution in Spheroidized Medium Carbon Steels using Crystal Plasticity‐Based Numerical Simulations

Microstructure and properties of ultrafine WC–Co–VC cemented carbides with different Co contents

A comprehensive constitutive equation for the hot deformation of WC-Co