Abstract:High entropy alloys (HEAs) have garnered significant attention in recent years, primarily focusing on alloying design and thermal processing. The objective of this study was to investigate the mechanical response of Al0.3CoCrFeNi, a representative HEA, under various stress states, temperatures, and strain rates, aiming to establish its constitutive equation and fracture criteria. Employing a hybrid FEM/EX approach, the constitutive behaviour of the alloy was characterized using the modified Johnson-Cook (MJC) model, while the fracture properties were assessed using the Hosford-Coulomb (HC) equation. Experimental findings highlighted the remarkable tensile strength (578.1 MPa) and ductility (69%) of the as-cast Al0.3CoCrFeNi at room temperature. However, at elevated temperatures ranging from 400 °C to 650 °C, a reduction in ductility was observed, accompanied by serration behaviour. Notably, precipitation hardening was detected at 800 °C, indicative of strengthening through precipitate formation. Additionally, Al0.3CoCrFeNi exhibited significant strain rate sensitivity and a positive strain rate effect, emphasizing its dynamic response under different loading conditions. The accuracy of the constitutive model and fracture criteria was validated through the examination of deformation and fracture modes in Taylor impact tests. The MJC model demonstrated predictions within a 10% deviation from experimental data, while the HC fracture criterion, accounting for stress triaxiality and Lode parameters, effectively predicted shear fracture in the projectiles. Crack formation in the projectiles resulted from a combination of tension and shear, followed by propagation at a 45° angle under combined compression and shear loading. This comprehensive study enhances understanding of the mechanical properties of Al0.3CoCrFeNi, providing valuable insights for its application in engineering, particularly in impact protection.

Coupling Residual Stress Field to Enhance the Simulation Accuracy of Crack Propagation and Mechanical Responses of High Entropy Ceramics Reinforced by Graphene and Alumina

A Lennard-Jones Potential Based Cohesive Zone Model and Its Application in Multiscale Damage Simulation of Graphene Reinforced Nanocomposites

An micro-level study on the cracking performance of encapsulation-based self-healing resin mineral composites under dynamic load based on XFEM

Monte Carlo simulation of complex cohesive fracture in random heterogeneous quasi-brittle materials

Progress in densification and toughening of high entropy carbide ceramics

Molecular simulation of microstructure evolution and plastic deformation of nanocrystalline CoCrFeMnNi high-entropy alloy under tension and compression

Toughening in low-dimensional nanomaterials high-entropy ceramic nanocomposite

Modeling damage evolution of graphene/aluminum composites considering crystal cracking and interface failure

Enhancing fatigue crack propagation resistance of heterostructured Al composites and multistage crack mechanisms

A Monte Carlo simulation of damage and failure process with crack saturation for unidirectional fiber reinforced ceramic composites

Atomistic simulation and experimental verification of tribological behavior of high entropy alloy/graphene composite coatings

Investigation of mechanical behavior, constitutive modeling, and fracture criteria for as-cast Al0.3CoCrFeNi high entropy alloy

Interfacial engineering for enhanced mechanical performance: High-entropy alloy/graphene nanocomposites

The oxide-layer configuration alteration and pseudo-ductile crack propagation mechanisms in composites induced by different relative thicknesses of CVI HfC-SiC multiphase matrix

Enhanced Mechanical Properties in Ceramic Multilayer Composites Through Integrating Crystallographic Texture and Second-Phase Toughening

Deformation and fracture of SiCp/Al composites under complex loading conditions: A simulation study

Theoretical modeling of toughening mechanisms in the CrMnFeCoNi high-entropy alloy at room temperature

Molecular Dynamics Simulation and Experimental Study of Mechanical Properties of Graphene–Cement Composites

Cracking behavior of newly-developed high strength eutectic high entropy alloy matrix composites manufactured by laser powder bed fusion

Microstructural origins of enhanced work hardening and ductility in laser powder-bed fusion 3D-printed AlCoCrFeNi 2.1 eutectic high-entropy alloys

Tailoring the toughening effects in two-dimensional nanomaterial-reinforced ceramic matrix composites