Abstract:The hole injection layer (HIL) plays a significant role in determining the performances of organic light-emitting diodes (OLEDs), especially when hole transport materials with deep highest occupied molecular orbital levels (HOMOs) are employed.Intensive efforts have been devoted to exploring novel hole injection materials with good solution-processing abilities in recent years.In this study, the solution-processed molybdenum trioxide (s-MoO3) is prepared via an ultra-facile method.Three different s-MoO3 layers prepared by three different methods, viz.layers annealed at 150 °C (s-MoO3 (150)), layers annealed at 150 °C and then processed in UV-ozone for 15 min (s-MoO3 (150, UVO)), and layers processed in UV-ozone for 15 min without annealing (s-MoO3 (UVO)), are obtained to investigate their influences on hole injection.The device with the s-MoO3 (150) layer has the lowest current density and the largest driving voltage, showing poor hole injection ability.In contrast, with the s-MoO3 (150, UVO) layer as HIL, the OLED produces a greatly enhanced current and sharply reduced driving voltage, comparable to the device using vacuum-evaporated MoO3.Similar results are obtained for the device with the s-MoO3 (UVO) film, suggesting that high-temperature annealing is not essential for the s-MoO3 film with UV-ozone treatment.Hole injection efficiencies of MoO3 films are quantitatively characterized by analyzing the space-charge-limited current of holeonly devices; the hole injection efficiencies of s-MoO3 (150, UVO) and s-MoO3 (UVO)-based devices are ~0.1, far exceeding that of the s-MoO3 (150)-based device (10 -5 ).XPS analysis is performed to detect the impact of the above treatments on the surface electronic properties of the s-MoO3 films.A typical characteristic of Mo 5+ species is obtained for the s-MoO3 (150) film and a high-binding-energy shoulder appears in the O 1s peak of the s-MoO3 (150) film, indicating the existence of oxygen vacancies and oxygen adsorbed at the surface of s-MoO3 (150) film.When UV-ozone treatment is applied to this s-MoO3 (150) film, it produces a decrease of Mo 5+ state and elimination of oxygen-rich adsorbates, resulting in MoO3 stoichiometry similar to that of the vacuum-evaporated MoO3 film.Consequently, a maximum current efficiency of 48.3 cd•A -1 is realized with the optimized UV-ozone treated s-MoO3 HIL.It This UV-ozone treated s-MoO3 should have widespread applications in low-cost solution-processed OLEDs as an excellent hole injection layer.

Hybrid Organic Light-Emitting Device Based on Ultrasonic Spray-Coating Molybdenum Trioxide Transport Layer with Low Turn-on Voltage, Improved Efficiency & Stability

Low Operating-Voltage and High Power-Efficiency OLED Employing MoO3-doped CuPc As Hole Injection Layer

Electroluminescence Performance Of Organic Light-Emitting Diode With Molybdenum Trioxide Inside Hole Transport Layer

Solution-processed MoOx Hole Injection Layer Towards Efficient Organic Light-Emitting Diode

An Efficient and Stable Hybrid Organic Light-Emitting Device Based on an Inorganic Metal Oxide Hole Transport Layer and an Electron Transport Layer

Solution Process Feasible Highly Efficient Organic Light Emitting Diode with Hybrid Metal Oxide Based Hole Injection/Transport Layer

Single-crystalline hole-transporting layers for efficient and stable organic light-emitting devices

Performances enhancement in OLEDs by inserting ultrathin trilayer in electron injection structure and using MoO3 as hole buffer layer.

Improved Performance with a Hybrid Cathodic Interfacial Layer in OLEDs

Solution-processed Molybdenum Oxide Hole Transport Layer Stabilizes Organic Solar Cells

Bipolar TADF Interlayer for High Performance Hybrid WOLEDs with an Ultrathin Non-Doped Emissive Layer Architecture

Disordered Nano‐Hemisphere Molybdenum Trioxide for Enhanced Light Out‐Coupling in Organic Light‐Emitting Diodes

Room-temperature sol-gel derived molybdenum oxide thin films for efficient and stable solution-processed organic light-emitting diodes.

Improved Hole Injection Property of Solution-Processed MoO<sub>3</sub> with UV-Ozone Treatment

Enhanced performance of organic electroluminescent diodes by UV-ozone treatment of molybdenum trioxide

Efficient Organic-Inorganic Hybrid Hole Injection Layer for Organic Light-Emitting Diodes by Aqueous Solution Doping

Mixed Organic Thin Films for Organic Light-emitting Diodes

Efficiency Enhancement of Organic Light-Emitting Diodes Via a Self-Assembled Moth-Eye Nanopatterned Hole-Transporting Layer.

Electro-optical performance of molybdenum oxide modified aluminum doped zinc oxide anodes in organic light emitting diodes: A comparison to indium tin oxide

Ultrasonic Spray Coating Polymer and Small Molecular Organic Film for Organic Light-Emitting Devices