Abstract:Acoustical methods are playing an important role for nondestructive evaluation (NDE) of adhesive-bonded composites and components in industrial applications. A dual-frequency ultrasonic technique is proposed for the quantitative evaluation of contact strength between pressed solid surfaces. An ultrasonic excitation consists of two primary frequency components is applied perpendicular to the interface, and the transmitted wave is examined. Theoretical study is based on a perturbation analysis of contact acoustic nonlinearity (CAN) model, predicting the generation of difference and sum frequency waves, together with the second harmonics. Nonlinear parameters are defined to describe the nonlinearity generation efficiencies. Experiments are performed for three types of interfaces, i. e. the interfaces of two aluminum alloy blocks with and without couplant and two glass blocks. The difference frequency wave component has bigger generation efficiency than other nonlinear components, which offers an advantage of high SNR and good detection capability of contact stiffness (interfacial stiffness). For each interface, the first and second-order interfacial stiffness are measured with contact pressure increasing from near zero to about 0.8 MPa with the aid of a laser interferometer. Finally, numerical simulations are also carried out, and a consistency is found between measurements and calculations. The dual-frequency ultrasound sent to the interface generates at least four second-order nonlinear components, which enriches the CAN technique for interface quality examinations. Both measured and simulated results indicate an increase of interfacial stiffness and decrease of nonlinear parameters with growing contact pressure. Moreover, measured results show that couplant between interfaces influences the contact stiffness evaluations in an enhanced manner, while the contact pressure determined by measured interfacial stiffness values are underestimated due to the couplant. The main problem comes from the contact between the transducersample interfaces, which brings extra nonlinearity to the detected signals and affect the accuracy of measuring. Copyright© (2010) by the International Congress on Acoustics.

Oblique-incidence Ultrasonic Testing for the Adhesion Quality of Ceramic Coatings

Research on Ultrasonic Testing Methods for Adhesion Quality of Ceramic Coatings

Effectiveness of phased array focused ultrasound and active infrared thermography methods as a nondestructive testing of Ni-WC coating adhesion

Ultrasonic Resonance Measuring for the Thickness of Ceramics Coatings

Assessment of the Adhesion of Ceramic Coatings

Interfacial Adhesion Measurement of a Ceramic Coating on Metal Substrate

A Novel High-Frequency Ultrasonic Approach for Evaluation of Homogeneity and Measurement of Sprayed Coating Thickness

Influence of Transparent Coating Hardness on Laser-Generated Ultrasonic Waves

Ultrasonic nondestructive evaluation of the bonding strength of polyurethane coatings based on feedforward comb filtering effect

The Inspection Of The Sliding Surface And Subsurface Of Plasma-Sprayed Ceramic Coatings Using Scanning Acoustic Microscopy

Evaluation of contact stiffness between solid-solid interfaces using dual-frequency ultrasound

Interface Stiffness Identification of Rough and Weak Bonded Interface Using Developed Ultrasonic Reflection Phase Derivative Spectrum

Nondestructive Measurement of Elastic Modulus for Thermally Sprayed WC-Ni Coatings Based on Acoustic Wave Mode Conversion by Small Angle Incidence

Thickness Measurement Approach for Plasma Sprayed Coatings Using Ultrasonic Testing Technique

Quantitative Characterization of the Interfacial Roughness and Thickness of Inhomogeneous Coatings Based on Ultrasonic Reflection Coefficient Phase Spectrum

Improvement of Adhesion and Cohesion in Plasma-Sprayed Ceramic Coatings by Heterogeneous Modification of Nonbonded Lamellar Interface Using High Strength Adhesive Infiltration

Ultrasonic Characterization for the Inhomogeneity of Thermal Barrier Coating Based on the Sound Pressure Reflection Coefficient Phase Spectroscopy

Nondestructive Evaluation of Adhesive Joints Using Nonlinear Non-collinear Wave Mixing Technique

Improvement of the Properties of Thermally Sprayed Ceramic Coating by the Infiltration of the Adhesives

Ceramic Coating and Laser Treatment

Three-dimensional Reconstruction and Porosity Calculation of Ceramic Coating: Nondestructive X-ray Computed Tomography