Abstract:Electrodeposited amorphous hydrated iridium oxide (IrOx) is a promising material for pH sensing due to its high sensitivity and the ease of fabrication. However, durability and variability continue to restrict the sensor's effectiveness. Variation in probe films can be seen in both performance and fabrication, but it has been found that performance variation can be controlled with potentiostatic conditioning (PC). To make proper use of this technique, the morphological and chemical changes affecting the conditioning process must be understood. Here, a thorough study of this material, after undergoing PC in a pH-sensing-relevant potential regime, was conducted by voltammetry, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Fitting of XPS data was performed, guided by raw trends in survey scans, core orbitals, and valence spectra, both XPS and UPS. The findings indicate that the PC process can repeatably control and conform performance and surface bonding to desired calibrations and distributions, respectively; PC was able to reduce sensitivity and offset ranges to as low as ±0.7 mV/pH and ±0.008 V, respectively, and repeat bonding distributions over ~2 months of sample preparation. Both Ir/O atomic ratios (shifting from 4:1 to over 4.5:1) and fitted components assigned hydroxide or oxide states based on the literature (low-voltage spectra being almost entirely with suggested hydroxide components, and high-voltage spectra almost entirely with suggested oxide components) trend across the polarization range. Self-consistent valence, core orbital, and survey quantitative trends point to a likely mechanism of ligand conversion from hydroxide to oxide, suggesting that the conditioning process enforces specific state mixtures that include both theoretical Ir(III) and Ir(IV) species, and raising the conditioning potential alters the surface species from an assumed mixture of Ir species to more oxidized Ir species.

The Effects of Cyclic Isothermal Oxidation on Ir/IrOxpH Electrode and a Method to Correct the Potential Drift of Metal Oxide Electrode

Effects of Structures on the Sensing Properties of Long-Term Stable IrOx Ph Electrodes

An Improved Method of Preparing Iridium Oxide Electrode Based on Carbonate-Melt Oxidation Mechanism

Experimental and Theoretical Constraints on Ph Measurements with an Iridium Oxide Electrode in Aqueous Fluids from 25 to 175 °C and 25 MPa

A Comparative Study of Fabricating IrOx Electrodes by High Temperature Carbonate Oxidation and Cyclic Thermal Oxidation and Quenching Process

Insight into the Factors of Thermal Oxidation Influencing Properties of Iridium Oxide Electrodes

Effects of Thermal Oxidation Cycle Numbers and Hydration on Irox Ph Sensor

A pH Electrode Based on Melt-Oxidized Iridium Oxide

Investigations of the Hydration Effects on Cyclic Thermo-Oxidized Ir/IrOx Electrode

Improvement of the Ir/IrO2 Ph Electrode Via Hydrothermal Treatment

A long-term stable iridium oxide pH electrode

Carbonate‐Melt Oxidized Iridium Wire for Ph Sensing

Nafion Modification of Thermal-Oxidized IrOxElectrode

Polarization Conforms Performance Variability in Amorphous Electrodeposited Iridium Oxide pH Sensors: A Thorough Surface Chemistry Investigation

Improved Iridium/iridium Oxide Ph Electrode Through Supercritical Treatment

Application of Cyclic Thermal-Oxidized IrOx Electrode in Ph Detection of Zn/Steel Galvanic Process in 3.5 Wt.% NaCl Solution

Performance of IrOx Ph Sensor Prepared by Electrochemical and Thermal Oxidation

Effect Of Oxidization Temperatures And Aging On Performance Of Carbonate Melt Oxidized Iridium Oxide Ph Electrode

Investigation of Metal-Doped IrO2 in Rotating Disk Electrode and Membrane Electrode Assembly Configurations for Acidic Oxygen Evolution Reaction

The Influences of Quenching Times on the Property of Thermal Oxidized Iridium Ph Sensor

Development of SPEEK-Coated IrOx Sensor for High-Biomass Aquatic Ph Monitoring