Abstract:The current study is aimed to evaluate the effect of nanomaterials (nano alumina (NA) and nano silica (NS) on the mechanical and durability performance of fiber-reinforced alkali-activated mortars (FRAAM). Polypropylene fiber (PPF) was added to the binders at 0.5% and 1% of the volume of the alkali-activated mortar (AAM). Design-expert software was used to provide the central composite design (CCD) for mix proportions. This method categorizes variables into three stages. The number of mixes was created and evaluated with varied proportions of variables. The primary binders in this experiment were 50% fly ash (FA) and 50% ground granulated blast slag (GGBS). The alkali-activated solution to binder ratio was 0.5, and the sodium hydroxide (NaOH) concentration was 12 molarity. The sodium silicate to sodium hydroxide ratio was 2.5. The cubic specimens and prisms were evaluated in an ambient atmosphere at 23 + 3 °C room temperature at the ages of 7 and 28 days. The mechanical performance of AAM was indicated through evaluation of the compressive and flexural strength, flowability, and unit weight of the alkali activator mortar. In addition, the durability performance and microstructure analysis were also evaluated. The experiments demonstrated that the AAM without fibers and nanomaterials had a higher flow rate than the other mixtures. However, the flowability of all mixtures was acceptable. The highest compressive strength was deducted through the use of 2% NA and higher flexural tensile strength was obtained for mixtures included 1% NS and 0.5% PPF. The lower water absorption was noted through the combination of 2% nano silica and 1% polypropylene fiber. Whereas, the combination of 2% nano silica, 1% nano alumina, and 0.5% polypropylene fiber had the lower sorptivity. In addition, the microstructure analysis indicated that the nanomaterials significantly improved the matrix and the porosity of the matrix was considerably reduced.

Performance of resin bonded sand for magnesium alloy casting

Performance Comparison and Mechanism Analysis of Several No-Bake Sand

Effect of Magnesium-containing Modifier on the Properties of Boron Aluminum Phosphate Inorganic Binder and Its Heat-cured Molding Sand

Effect of Reclaimed Sand Additions on Mechanical Properties and Fracture Behavior of Furan No-Bake Resin Sand

3D Printed (Binder Jetting) Furan Molding and Core Sands—Thermal Deformation, Mechanical and Technological Properties

Effect of Additives on Heat Hardened Inorganic Solid Foundry Binder

Study of Environmentally Friendly Phosphate-Bonded No-Bake Sand

A New Phosphate Binder for Making Sand Mold or Core for Aluminum Alloy Castings

Study on the Gas Release of 3D-Printed Furan Resin Sand Core During the Casting Process

Effects of Processing Parameters and Addition of Flame-Retardant into Moulding Sand on the Microstructure and Fluidity of Sand-Cast Magnesium Alloy Mg-10gd-3y-0.5zr

Fabrication and posttreatment for inorganic binder jetting sand molds for casting

Mechanical Behavior of Cemented Sand Reinforced with Different Polymer Fibers

Performance of Fiber-Reinforced Alkali-Activated Mortar with/without Nano Silica and Nano Alumina

Study On Properties And Effects Of A New Heat Cured Inorganic Foundry Binder

Discuss of Bond Mechanism of AI-phosphate Hot Cured Sand

Research on New Al-Mg-B Compound Phosphate Inorganic Binder for Heat Cured Sand

Combined Influences of Cement, Rice Husk Ash and Fibre on the Mechanical Characteristics of a Calcareous Sand

Mechanism of Strength Loss of No-Bake Phosphate Bonded Sand Mold/core

Hybrid Filler Actions on Functional Performance Evaluation of Magnesium Alloy (AZ61) Hybrid Nanocomposites

Study on the Storage Stability of High Neutralization Degree Phosphate-Bonded No-Bake Sand

Effect of Boron-contaning Modifier on the Properties of Heat-cured Aluminum Phosphate Inorganic Binder-bonded Sand