Abstract:The 2195 Al-Cu-Li alloy is widely utilized for the fabrication of key aerospace vehicle components; hence, an in-depth understanding of its hot deformation behavior is essential for consistently achieving high-performance products. In this study, isothermal compression tests were performed on 2195 Al-Cu-Li alloy ingots in the temperature and strain rate ranges of 250–500 °C and 10 −3 -1 s −1 , respectively. A processing map was established to predict the workability under different conditions. The corresponding microstructures were examined to reveal their hot deformation mechanism. Results demonstrated that the processing map was divided into four distinct domains. The unstable zone was located in the 250–375 °C/10 −1.5 -1 s −1 and 250–275 °C/10 −2.5 –10 −1.5 s −1 , temperature/strain rate regimes, in which deformation bands and flow localization were observed. The deformation bands blocked dislocations and compromised the dynamic recrystallization (DRX) behavior, hence damaging the microstructure. Further, large coarse T 1 phases precipitated in the 325–410 °C/10 −2.5 –10 −3 s −1 regime, which led to the formation of heterogeneities in the microstructure, corresponding to a minimum workability in the processing map. The optimal hot-working domain for the 2195 alloy was determined to be 460–500 °C/10 −3 –10 −2 s −1 , and the dominating hot deformation mechanisms were DRX and dynamic recovery (DRV). Specifically, continuous and discontinuous DRX behaviors dominated in the 300–400 °C/10 −3 s −1 and 450–500 °C/10 −3 s −1 regimes, respectively. DRX gradually weakened as the strain rate increased at 500 °C. Further, the weakening of DRX was only minimally affected by temperature at 400–500 °C during high-speed deformation (1 s −1 ). The results reported herein can provide valuable insights into the hot working of Al-Cu–Li alloys.

Characterization of Hot Deformation Behavior of AA2014 Forging Aluminum Alloy Using Processing Map

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Processing Map of GH4169 Alloy During Hot Plastic Deformation

Hot Deformation and Processing Maps of 7005 Aluminum Alloy

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys

3D Processing Map and Hot Deformation Behavior of 6A02 Aluminum Alloy

Hot Processing Map and Dynamic Precipitation Behavior of 1460 Al–Li Alloy During Hot Deformation

Effect of Initial Microstructure on the Hot Deformation Behavior and Microstructure Evolution of Aluminum Alloy AA2060

Hot Deformation Behavior and Microstructural Evolution of a New Type of 7xxx Al Alloy

Hot Deformation Characteristics and Processing Parameter Optimization of Al–6.32Zn–2.10Mg Alloy Using Constitutive Equation and Processing Map

Hot deformation characteristics and processing parameter optimization of 2219 Al alloy using constitutive equation and processing map

Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: A study with processing map

Hot deformation characteristics and processing maps of AA7075-H18 alloy sheet under hot forming process conditions

Hot Deformation Behavior and Processing Maps of 2099 Al-Li Alloy

Constitutive behavior and novel characterization of hot deformation of Al-Zn-Mg-Cu aluminum alloy for lightweight traffic

The Study on Forming Property at High Temperature and Processing Map of 2219 Aluminum Alloy

Characterization on Hot Deformation Behavior of Ti-22Al-25Nb Alloy Using a Combination of 3D Processing Maps and Finite Element Simulation Method

Characterization of the Hot Deformation Behavior of a Ti–22Al–25Nb Alloy Using Processing Maps Based on the Murty Criterion

Comprehensive study of hot compression behaviors and microstructure evolution of solutionized 6082 aluminum alloy extruded bar

Hot Workability of a Spray Formed 2195 Aluminum-Lithium Alloy Based on an Improved Isothermal Processing Map and Drx ‘C-Curve’

Characterization of the hot deformation behavior of a Al-Si alloy using processing maps