Abstract:This study deals with the Nb–niobium silicide-based composites developed by the hot-pressing of Nb–Si–Ti ternary powder mixtures with a fixed Ti addition (6at.%) and Si content ranging from hypereutectic (11at.%) to near-eutectic compositions (18at.%). The effects of Si content, Ti addition and strain rates on the sample microstructural characterization, flexural strength, fracture toughness, quasi-static compressive deformation and failure processes were investigated. It was revealed that the volume fraction of silicides increased with increasing Si content, and most of the Ti atoms dissolved into the niobium silicides to form (Nb,Ti)5Si3 solid solutions instead of binary titanium silicides. The experimental evidence showed that a moderate improvement in the flexural strength, fracture toughness and compressive yield stress of the composites was achieved by the addition of Ti. Higher Si additions produced a much more remarkable enhancement in the compressive yield stress and bulk hardness, whereas both the flexural strength and fracture toughness decreased with increasing Si content owing to the existence of residual porosities in the samples. The composites showed remarkable superiority to the arc-melted Nb–Si alloys and monolithic niobium silicides in fracture toughness (8.3–13.0MPam vs. 4.5MPam), where the toughening effect was attributed mainly to crack bridging and crack deflection by the remaining ductile Nb phase. Moreover, quasi-static uniaxial compression tests at strain rates between 10–5 and 10–3s−1 indicated that the deformation behavior and failure processes were significantly affected by Si content and strain rates. The strain-rate-hardening behavior for all the strain rates was observed in the composite materials and the strain-rate sensitivity decreased with increasing Si content. At a lower strain rate, the composite materials with a hypoeutectic Si composition failed with a pseudoplastic response and at an angle of ∼45° off the compressive loading direction. However, in the case of higher strain rate and Si content, the brittle failure in the samples occurred through vertical splitting and spalling of fragments.

Microstructures and Mechanical Properties of Melt Hydrogenated Nb-Si Based Alloy

Experimental and Theoretical Investigation on the Enhanced Hydrogen Storage Performance of Ti–Cr–Mn–Fe-Based Alloys Modified by Nb Substitution

Microstructures And Hydrogen Desorption Properties Of The Mgh2-Alh3 Composite With Nbf5 Addition

Effect of hydrogen on deformation induced phase transformation and hot workability of Ti2AlN/Ti46Al4Nb1Mo composites

Evolution of Unidirectional Solidification Microstructure and Hydrogenated Treatment of Nb-Ti-Co Quasiperitectic Alloys

Towards enhancing the hot deformability of Ti 2 AlN/Ti46Al4Nb1Mo composites via melt hydrogenation

Microstructure and Room Temperature Mechanical Properties of Hf and Sn-Doped Nb-20ti-5cr-3al-18si Alloy

Microstructure, Phase Transformation and Mechanical Property of Nb-doped Ni–Mn–Ga Alloys

Microstructure and Mechanical Properties of Refractory Hfmo0.5nbtiv0.5six High-Entropy Composites

Effect of Nb-Content on Mechanical Properties of (Ni<sub>47</sub>Ti<sub>44</sub>)<sub>100-x</sub>Nb<sub>x</sub> Shape Memory Alloys

Effect of Mo and Nb on mechanical properties and hydrogen embrittlement of hot-rolled medium-Mn steels

Hot Deformation Behavior and Microstructural Characteristics of Ti–46Al–8Nb Alloy

Hydrogen Permeable Nb-Based Amorphous Alloys with High Thermal Stability

Microstructure Evolution and Toughening Mechanism of a Nb-18Si-5HfC Eutectic Alloy Created by Selective Laser Melting

Effect of deformation parameters on microstructural evolution during hot compression of Nb–V–Mo microalloyed steel

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Effect of silicon addition on the microstructures, mechanical properties and helium irradiation resistance of NiCoCr-based medium-entropy alloys

Microstructure and Mechanical Properties Determined in Compressive Tests of Quasi-Rapidly Solidified NiAl-Cr(Mo)-Hf Eutectic Alloy after Hot Isostatic Pressure and High Temperature Treatments

Elevated Temperature Compressive Behavior of Nb-22Ti-16Si-7Cr-3Al-3Ta-2Hf Alloy with Minor Ho Addition

Effects of Si variation and Zr addition on the microstructure, oxidation resistance and mechanical property at 1523 K of Nb-Si-Ti/Zr/Hf-Cr/Al high-entropy superalloys

Effects of annealing temperature and heating rate on microstructure, magnetic, and mechanical properties of high-Bs Fe81.7−xSi4B13NbxCu1.3 nanocrystalline alloys