Abstract:This paper presents the first experimental engine and test rig results obtained from a fast response cooled total pressure probe. The first objective of the probe design was to favor continuous immersion of the probe into the engine to obtain a time series of pressure with a high bandwidth and, therefore, statistically representative average fluctuations at the blade passing frequency. The probe is water cooled by a high pressure cooling system and uses a conventional piezoresistive pressure sensor, which yields, therefore, both time-averaged and time-resolved pressures. The initial design target was to gain the capability of performing measurements at the temperature conditions typically found at high pressure turbine exit (800–1100°C) with a bandwidth of at least 40 kHz and in the long term at combustor exit (2000 K or higher). The probe was first traversed at the turbine exit of a Rolls-Royce Viper turbojet engine at exhaust temperatures around 750°C and absolute pressure of 2.1 bars. The probe was able to resolve the high blade passing frequency (≈23 kHz) and several harmonics of up to 100 kHz. Besides the average total pressure distributions rom the radial traverses, phase-locked averages and random unsteadiness are presented. The probe was also used in a virtual three-hole mode yielding unsteady yaw angle, static pressure, and Mach number. The same probe was used for measurements in a Rolls-Royce intermediate pressure burner rig. Traverses were performed inside the flame tube of a kerosene burner at temperatures above 1600°C. The probe successfully measured the total pressure distribution in the flame tube and typical frequencies of combustion instabilities were identified during rumble conditions. The cooling performance of the probe is compared with estimations at the design stage and found to be in good agreement. The frequency response of the probe is compared with cold shock-tube results and a significant increase in the natural frequency of the line-cavity system formed by the conduction cooled screen in front of the miniature pressure sensor were observed.

Investigation on Transient Temperature of a Reciprocating Compressor Based on a Two-Thermocouple Probe

Ito Thin Film Thermocouple For Transient High Temperature Measurement In Scramjet Combustor

Transient Thermal Analysis of the Rotary Compressor During Startup Process

Theoretical and Experimental Study for the Transient Behavior of a Linear Compressor During Pulse Tube Cryocooler Cool Down Process

Performance Evaluation on the In-Cylinder Heat Transfer of a Reciprocating Compressor Using CO 2 As a Working Fluid

Investigation of Interaction Between Thermodynamic Processes and Pressure Pulsation Based on Transient CFD Model of a Reciprocating Compressor

Experimental Study on Supersonic Combustion Fluctuation Using Thin-Film Thermocouple and Time–frequency Analysis

Comparison of Temperature Difference Measurement Technologies Used in Vehicular Heat Exchangers

Temperature Measurement by Thermocouple Probe: Influences of Variable Fluid Velocity on the Dynamic Characteristics of Thermocouple

Heat Transfer Simulation for Reciprocating Compressor with Experimental Validation

On the Response of Coaxial Surface Thermocouples for Transient Aerodynamic Heating Measurements

Transient Response Characteristics and Performance Assessment of a Calorimetric Surface Junction Probe Under Impulsive Thermal Loading

Unsteady Pressure Measurements With a Fast Response Cooled Probe in High Temperature Gas Turbine Environments

Research on a dedicated thin-film thermocouple testing system for transient temperature measurement

Simulation, Fabrication, and Characteristics of High-Temperature, Quick-Response Tungsten–rhenium Thin-Film Thermocouples Probe Sensor

Determination of Local Heat Transfer Coefficient Based on Bulk Mean Temperature Using a Transient Liquid Crystals Technique

Uncertainties of the Transient Thermochromic Liquid Crystal Method in Gas Turbine Internal Cooling Measurements

Experimental and numerical analysis of heat transfer mechanisms for two-phase oil-refrigerant flow process in the cylinder of rotary compressor

The single-blow transient test technique using pulse change inlet condition with optimized pulse width and matching time

Tentative Research about Pressure Measurement on One Point of Compressor Rotor Blade Surface

Development of a high temperature cooled fast response probe for gas turbine applications