Abstract:Electric vehicles are being developed to address environmental issues such as air pollution caused by vehicles that use fossil fuels. As a result, the efficiency and performance of the battery, which is a crucial component of an electric vehicle, have become increasingly important. Research on the electrical behavior and heat of the battery is currently being actively conducted. However, with the improvement of battery efficiency and the increase in mass production, safety issues have arisen. Numerous studies are being conducted on battery safety, such as thermal runaway resulting from the deformation and failure of battery components, including the cathode and anode, caused by loads acting on the battery. Recently, research on stress factors caused by random vibrations and shocks that reflect actual vehicle operating conditions has made significant progress. For instance, Brand et al. conducted random vibration and shock tests based on the UN 38.3 standard test, evaluating durability based on the increase in resistance that occurs during the test 1) . Similarly, Berg et al. tested cylindrical cells with random profiles, according to the SAE J2380 standard and an even more severe profile 2) . After the test, they mainly observed the deformation of the tab, rather than the jellyroll of the battery. Yun et al. created a numerical model with the Representative Volume Element (RVE) model at the module level, obtaining the effective elastic modulus from the RVE model of the cell level and applied it to the module, so that the behavior of the jellyroll was not described at the cell level 3) . However, previous studies have mainly analyzed battery degradation caused by vibration and shock tests based on electrical characteristics. Hence, further research on damage and numerical models of battery cell levels that cause degradation according to random vibration and shock tests is required. In this study, anode, cathode, and separator of a pouch cell were prepared in form of a rectangular specimen with notch to conduct vibration and shock tests using the UN 38.3 standard test. The three battery cell components were stacked on a vibration jig, as in a real pouch cell. Scanning electron microscope (SEM) was used to investigate whether a fracture like crack occurred due to a vibration test near the notch of the specimen with a. Additionally, a numerical model for the pouch cell was constructed using a representative sandwich (RS) model 4) , and the predicted fracture behavior of the battery components according to the vibration and shock test was analyzed. The RS model provided a simplified representation of the internal structure of a battery cell, and the mechanical parameters required to build the RS model were obtained through tensile tests of battery cell components. Brand, Martin J., et al. "Effects of vibrations and shocks on lithium-ion cells." Journal of Power Sources 288 (2015): 62-69. Berg, Philipp, et al. "Durability of lithium-ion 18650 cells under random vibration load with respect to the inner cell design." Journal of Energy Storage 31 (2020): 101499. Jin Chul Yun. "Study on mechanical behavior of lithium ion battery using multi-scale analysis.". (2017). Pohang University of Science and Technology, PhD dissertation Zhang, Chao, et al. "A representative-sandwich model for simultaneously coupled mechanical-electrical-thermal simulation of a lithium-ion cell under quasi-static indentation tests." Journal of Power Sources 298 (2015): 309-321.

Failure behaviours of 100% SOC lithium-ion battery modules under different impact loading conditions

INFLUENCE OF MECHANICAL INTERACTION BETWEEN LITHIUM-ION POUCH CELLS IN A SIMPLIFIED BATTERY MODULE UNDER IMPACT LOADING

Dynamic crushing behaviors and failure of cylindrical lithium-ion batteries subjected to impact loading

Dynamic Crushing Behaviors of Cylindrical Lithium-Ion Battery Under Multiple Impacts: An Experimental Study

Experimental Study on the Effect of State of Charge on Failure Propagation Characteristics Within Battery Modules

Fracture Mode Analysis of Lithium-Ion Battery under Mechanical Loading

Deformation and Failure Properties of High-Ni Lithium-Ion Battery under Axial Loads

Experiments and 3D detailed modeling for a pouch battery cell under impact loading

A novel anisotropic model for multi-stage failure threshold of Lithium-ion battery subjected to impact loading

Failure mechanism and predictive model of lithium-ion batteries under extremely high transient impact

Experimental investigation of thermal failure propagation in typical lithium-ion battery modules

Mechanism of failure behaviour and analysis of 18650 lithium-ion battery under dynamic loadings

Dynamic Multi‐Physics Behaviors and Performance Loss of Cylindrical Batteries Upon Low‐Velocity Impact Loading

Analysis of Internal Short Circuit and Thermal Runaway of Li-Ion Battery Due to Mechanical Abuse

Safety Performance and Failure Criteria of Lithium-Ion Batteries under Mechanical Abuse

Characterization of Behavior of Lithium Ion Battery Under Vibration and Shock Conditions

Thermal Failure Propagation in Lithium-Ion Battery Modules with Various Shapes

Coupling Effect of State of Charge and Loading Rate on Internal Short Circuit of Lithium-Ion Batteries Induced by Mechanical Abuse

Dynamic impact response of lithium-ion batteries, constitutive properties and failure model

Prediction of Shear Crack Formation of Lithium-Ion Batteries under Rod Indentation: Comparison of Seven Failure Criteria

Experimental study on the dynamic behavior of prismatic lithium-ion battery upon repeated impact