Abstract:This paper proposes a MEMS resonant pressure sensor through implementing an out-of-plane repulsive (levitation) force to enhance the sensor detection threshold and consequently widen its sensing range. 2D and 3D finite-element simulations are conducted and compared to some available experimental data. The simulated results show an increase in the generated levitation force as outstanding merit owing to the added side upper electrodes. The levitation force is then further increased by lateral spacing optimization in association with the assumed applied voltage, which decreases the overall size (footprint) as well. The dynamical behavior around the static equilibrium is first numerically solved using the so-called shooting technique and then compared with an available online simulation tool: the "Matcont" package. The simulated results prove the capability of the online simulator to capture the dynamic response of the resonant micro-sensor when approaching its respective bifurcation points where the stable and unstable branches collide, when in contrary, the shooting technique failed to get the dynamic responses when passing by these bifurcations. Thanks to the fast converging outcomes of the "Matcont" online simulation equipped with simultaneous stability analysis, a comprehensive analysis of the micro-sensor dynamical response is conducted. Three sensing mechanisms as: measurements of frequency shift, amplitude alternation, and amplitude rise/fall near a bifurcation region are evaluated and characterized. Along with enumerating the strengths of the proposed sensor over the conventional capacitive pressure sensors, the advantage of measuring the amplitude rise/fall near the corresponding bifurcation region comparing to the two other sensing mechanisms is detailed, and its possible failure for performance repeatability is resolved by means of the slow-varying frequency sweep. Unlike the traditional parallel-plate configuration in which only one-side frequency shift is observed, in this proposed design, two-sides frequency shift is detected, and accordingly, the reinitialization is categorized based on that. As compared to the conventional MEMS pressure sensor, this revisited design equipped with the suggested sensing mechanism offers wider tunability and sensing range, resolution power enhancement, and simplification of the signal processing circuit.

Vibration Modes Interference in the MEMS Resonant Pressure Sensor

Analysis of the Frequency-Dependent Vibration Rectification Error in Area-Variation-Based Capacitive MEMS Accelerometers.

High Accuracy Resonant Pressure Sensor With Balanced-Mass DETF Resonator and Twinborn Diaphragms

A New Type of MEMS Accelerometer with Up-Tuning Structure

High Sensitivity Micro Electrometer Based On Clamped Free Curved Beams Resonator With Weakened Nonlinearity

Experimental Verification of Coupling Strength on the Mode-Localization in Single MEMS DETF Resonators and Its Application as a Force Sensor

Electrical Adjustment on a MEMS Double-Ended-tuning-fork Resonator

A Mems Accelerometer Based On Synchronizing Detf Oscillators

Design and fabrication of a novel all-quartz resonant pressure sensor with continuously variable section of DETF

All-Quartz High Accuracy MEMS Pressure Sensor Based on Double-Ended Tuning Fork Resonator

A Micro Resonant Charge Sensor with Enhanced Sensitivity Based on Differential Sensing Scheme and Leverage Mechanisms

Design and Optimization of MEMS Resonant Pressure Sensors with Wide Range and High Sensitivity Based on BP and NSGA-II

Design and implementation of a fully-decoupled tuning fork (FDTF) MEMS vibratory gyroscope for robustness improvement

A High-sensitivity, Small-size Resonant Pressure Microsensor Based on Optimized Resonator-diaphragm Structure.

A MEMS Resonant Differential Pressure Sensor With High Accuracy by Integrated Temperature Sensor and Static Pressure Sensor

Electrostatic Charge Sensor Based on Micro Resonator with Sensing Scheme of Effective Stiffness Perturbation

A resonant pressure MEMS sensor based on levitation force excitation detection

MEMS gyroscope structure with low mechanical-thermal noise and weak mechanical coupling

A MEMS Resonant Accelerometer with Sensitivity Enhancement and Adjustment Mechanisms

An adjustable pre-stress based sensitivity enhancement scheme for cantilever-based resonant sensors

A Novel Mechanical Frequency Tuning Method Based on Mass-Stiffness Decoupling for MEMS Gyroscopes