Abstract:Organic photovoltaics (OPVs) have been considered as one of the preliminary candidates for the third-generation solar cells due to their particularly advantages, such as light-weight, low cost, solution processability and mechanical flexibility. In recent years, the power conversion efficiency (PCE) of OPVs has achieved remarkable progress with the development of non-fullerene acceptors (NFAs), which exhibit stronger capability of light absorption and stability than the fullerene acceptors. However, the narrow absorption properties of organic materials still restrict the further breakthrough of the performance of OPVs. It is difficult for the binary heterojunction films to realize the effective wide spectrum utilization of solar energy. Ternary strategy, which consists of one donor and two acceptors or two donors and one acceptor in a bulk-heterojunction, has proven to be an effective and facile way to enhance performances of OPVs. The emergence of new NFAs such as ITIC, IT-4F, Y6 etc. greatly increases the selectivity of acceptors in a ternary system. It is necessary to investigate the compatibility of latest NFA materials and corresponding ternary device performance. In this article, we report a new ternary OPV system with dual NFAs and a polymer donor. The excellent NFA material (Y6), which was first reported in 2019, is used as the third component. Different concentrations of Y6 are introduced into the binary system based on PBDB-T-2F:IT-4F. The compatibility between materials and device performances are investigated through absorption capability of blend films, AFM, water contact angle, GISAXS, and corresponding electrical properties of devices. The 12.48% PCE is achieved from ternary OPVs with PBDB-T:IT-4F as the active layers containing 20wt% Y6 in acceptors, resulting from the enhanced Jsc of 22.09 mA/cm2, Voc of 0.83 V and FF of 68.45%. The origin of the improvement of the ternary OPVs is summarized below. Firstly, an apparently complementary absorption spectrum is obtained through the introduction of Y6, which has a stronger photo harvesting capability in the spectral range from 750 to 950 nm than IT-4F, and higher short current density (Jsc) is observed in the ternary devices than in the binary device. Secondly, a rougher surface of the active layer is observed by increasing the Y6 concentration, which may result in an inferior exciton dissociation and charge transport process, the existence of larger-scaled crystal is proved by the GISAXS technology. Thirdly, the introduced Y6 can help to suppress the bimolecular recombination, which is in favor of the incremental device performance. Approximately 17.85% PCE improvement is obtained in comparison with PBDB-T-2F:IT-4F based binary OPVs.

Polymer Solar Cells: Improved Performance of Ternary Polymer Solar Cells Based on A Nonfullerene Electron Cascade Acceptor (adv. Energy Mater. 11/2017)

High-Performance Ternary Organic Solar Cells Enabled by Synergizing Fullerene and Non-fullerene Acceptors

Improved Performance of Ternary Polymer Solar Cells Based on A Nonfullerene Electron Cascade Acceptor

Improved Charge Transport and Reduced Nonradiative Energy Loss Enable over 16% Efficiency in Ternary Polymer Solar Cells

Highly Efficient Ternary Solar Cells with Efficient Förster Resonance Energy Transfer for Simultaneously Enhanced Photovoltaic Parameters

Enhanced Photovoltaic Performance of Ternary Polymer Solar Cells by Incorporation of a Narrow-Bandgap Nonfullerene Acceptor

Cyclopentadithiophene Cored A-π-D-π-A Non-Fullerene Electron Acceptor in Ternary Polymer Solar Cells to Extend the Light Absorption Up to 900 Nm

Ternary Blended Fullerene‐Free Polymer Solar Cells with 16.5% Efficiency Enabled with a Higher‐LUMO‐Level Acceptor to Improve Film Morphology

Using Ternary Blend As a Strategy to Improve the Driving Force for Charge Transfer and Facilitate Electron Transport in Polymer Solar Cells

Isomerization Directed Molecular Packing toward Suppressing Energy Loss in Nonfullerene Ternary Solar Cells

High-Performance Ternary Nonfullerene Polymer Solar Cells with Both Improved Photon Harvesting and Device Stability.

2D/1A Ternary Blend System Enables Non-Fused Ring Electron Acceptor Based Polymer Solar Cells with Improved Photovoltaic Parameters

Dual Non-Fullerene Acceptors Based High Efficiency Ternary Organic Solar Cells

High Efficiency Ternary Nonfullerene Polymer Solar Cells with Two Polymer Donors and an Organic Semiconductor Acceptor

Improving the Efficiency and Stability of Non-Fullerene Polymer Solar Cells by Using N2200 As the Additive

Ternary-Blend Polymer Solar Cells Combining Fullerene and Nonfullerene Acceptors to Synergistically Boost the Photovoltaic Performance

Ternary Polymer Solar Cells with High Efficiency of 14.24% by Integrating Two Well‐Complementary Nonfullerene Acceptors

High-Performance Ternary Organic Solar Cells through Incorporation of a Series of A 2 -A 1 -D-A 1 -A 2 Type Nonfullerene Acceptors with Different Terminal Groups

High Performing Ternary Solar Cells Through Förster Resonance Energy Transfer Between Nonfullerene Acceptors.

High-efficiency Ternary Nonfullerene Polymer Solar Cells with Increased Phase Purity and Reduced Nonradiative Energy Loss

Improved photovoltaic performance and robustness of all-polymer solar cells enabled by a polyfullerene guest acceptor