Abstract:A lithium-sulfur (Li-S) battery has a high theoretical specific capacity (1675 mAh g-1 of elemental sulfur) and a high nominal energy density (2500 Wh kg-1 of cell weight), which offers the prospect of a significant energy density improvement compared to the mainstream lithium-ion batteries (150 Wh kg-1). However, the development of Li-S battery technology has been plagued by problems arising from the highly insulating nature of sulfur (5×10-30 S cm-1 at 25 °C), the high solubility of lithium polysulfides in the electrolyte and volumetric expansion of sulfur during lithiation. Here, we demonstrate the design and preparation of few-layer graphene (FLG) foam scaffold for sulfur loading to fabricate cathode structures for lithium-sulfur batteries. In this work, a free-standing FLG monolithic network foam was formed as a negative of a Ni metallic foam template by CVD followed by etching away of Ni. Then, a three-dimensional (3-D) cathode system for lithium sulfur (Li-S) batteries has been synthesised by loading sulfur on to this interconnected network of few-layered graphene (FLG) via a sulfur solution infiltration method. This cathode system did not require any additional binding agents, conductive additives or a separate metallic current collector thus decreasing the weight of the cathode by typically ~20-30 wt%. A Li-S battery with the sulfur/FLG foam cathode shows good electrochemical stability and high rate discharge capacity retention for up to 400 discharge/charge cycles at a high current density of 3200 mA g-1, which due to the FLG foam offers excellent electrical conductivity, an appropriate pore structure for containing the electro-active sulfur and facilitates rapid electron/ion transport. Even after 400 cycles the capacity decay is only ~0.064% per cycle relative to the early (e.g. the 5th cycle) discharge capacity, while yielding an average columbic efficiency of ~96.2%. To further understand the sulfur loading ability of FLG foam, the composites with high content (up to 72 wt %) were also investigated. The composite with high content of sulfur still presented good initial discharge capacity and good cycle stability after 200 cycles. Our results indicate the potential suitability of graphene foam for efficient and high-performance batteries.

3D N-Doped Graphene Nanomesh Foam for Long Cycle Life Lithium-Sulfur Battery

High Sulfur Loading Composite Wrapped By 3d Nitrogen-Doped Graphene As A Cathode Material For Lithium-Sulfur Batteries

A High‐energy‐density Long‐cycle Lithium–sulfur Battery Enabled by 3D Graphene Architecture

One-step Synthesis of 3D N-doped Graphene Supported Metal Oxide for High Performance Li-S Battery

N-Doped Graphene Quantum Dots Supported by Carbon Nanotubes Grown on Carbon Clothes for Lithium Storage

Carbon-nanotube/sulfur Cathode with In-Situ Assembled Si3N4/graphene Interlayer for High-Rate and Long Cycling-Life Lithium-Sulfur Batteries

Powder metallurgy template growth of 3D N-doped graphene foam as binder-free cathode for high-performance lithium/sulfur battery

Enhanced Cycle Performance in a Binder Free Lithium Sulfur Battery Using Few-Layer Graphene Foam Scaffold

3D Dual-Confined Sulfur Encapsulated in Porous Carbon Nanosheets and Wrapped with Graphene Aerogels As A Cathode for Advanced Lithium Sulfur Batteries

Three-Dimensional Sulfur/Graphene Multifunctional Hybrid Sponges for Lithium-Sulfur Batteries with Large Areal Mass Loading

Binder Free Three-Dimensional Sulphur/few-Layer Graphene Foam Cathode with Enhanced High-Rate Capability for Rechargeable Lithium Sulphur Batteries

Sulfur Nanogranular Film-Coated Three-Dimensional Graphene Sponge-Based High Power Lithium Sulfur Battery

High-rate, Ultralong Cycle-Life Lithium/sulfur Batteries Enabled by Nitrogen-Doped Graphene.

High‐Performance Lithium‐Sulfur Batteries with a Self‐Supported, 3D Li2S‐Doped Graphene Aerogel Cathodes

Porous Three-Dimensional Reduced Graphene Oxide for High-Performance Lithium-Sulfur Batteries

Dual‐Confined Flexible Sulfur Cathodes Encapsulated in Nitrogen‐Doped Double‐Shelled Hollow Carbon Spheres and Wrapped with Graphene for Li–S Batteries

Preparation of Three-dimensional Nitrogen-doped Carbon Nanoribbon and Application in Lithium/Sulfur Batteries

Sulfur/three-dimensional graphene composite for high performance lithium–sulfur batteries

Tailoring 3D Carbon Foam using CNTs and MnO 2 to Fabricate Stable Lithium/Dissolved Lithium Polysulfide Batteries

Hierarchical 3D nitrogen and phosphorous codoped graphene/carbon nanotubes–sulfur composite with synergistic effect for high performance of lithium–sulfur batteries

Hierarchical nitrogen-doped porous graphene/reduced fluorographene/sulfur hybrids for high-performance lithium-sulfur batteries.