Abstract:The application of Li-ion conducting garnet electrolytes is challenged by their large interfacial resistance with the metallic lithium anode and the relative small critical current density at which the lithium dendrites short-circuit the battery. Both of these challenges are closely related to the morphology and the structure of the garnet membranes. Here, we prepared four polycrystalline garnet Li6.4La3Zr1.4Ta0.6O12 (LLZTO) pellets with different particle sizes (nano/micro) and grain boundary additive (with/without Al2O3) to investigate the influence of grain size, the composition of the grain boundary, and the mechanical strength of the pellet on the total Li-ion conduction of the pellet, Li/garnet interfacial transfer, and lithium dendrite growth in all-solid-state Li-metal cells. The results showed that the garnet pellets prepared with nanoparticles and LiAlO2-related grain boundary phase had decreased total Li-ion conductivity because of the increased resistance of the grain boundary; however, these pellets showed higher mechanical strength and improved capability to suppress lithium dendrite growth at high current densities. By controlling the grain size and optimizing the grain boundary with Al2O3 sintering additive, the hot-pressing sintered LLZTO solid electrolytes can reach up to 1.01 × 10–3 S cm–1 in Li+ conductivity and 0.29 eV in activation energy. LLZTO with nanosized grain and LiAlO2-modified grain boundary showed the highest critical current density, which is 0.6 mA cm–2 at room temperature and 1.7 mA cm–2 at 60 °C. This study offers a useful guideline for preparing a high-performance LLZTO solid electrolyte.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c18674?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c18674</a>.Feature sizes of LLZTO powders prepared by hand milling and sand milling (Table S1); XRD patterns of hot-pressing sintered samples (Figure S1); element distribution on the polished surface of the sintered samples containing Al2O3 and without Al2O3 by EDX scan (Figure S2); equivalent circuit model for EIS fitting (Figure S3); and LLZTO specimens fractured by three-point bending test, gold sprayed on the surface of the micro-solid electrolyte, an optical photo of the micro-lithium symmetrical battery, and a micro-test fixture designed to test the micro-battery (Figure S4) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c18674/suppl_file/am0c18674_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Improvement of the Conductivity of Sol-Gel Derived Li-La-Zr-O Thin Films by the Addition of Surfactant

Sol–gel Derived Li–La–Zr–O Thin Films As Solid Electrolytes for Lithium-Ion Batteries

Effect Temperature for improving the Li-ion conductivity of Li7La3Zr2O12

Ionic conductivity properties of amorphous Li–La–Zr–O solid electrolyte for thin film batteries

The “filler effect”: A study of solid oxide fillers with β-Li3PS4 for lithium conducting electrolytes

Influence of Zr aggregation on Li-ion conductivity of amorphous solid-state electrolyte Li-La-Zr-O

Isomeric Li–La–Zr–O Amorphous–Crystalline Composite Thin-Film Electrolytes for All-Solid-State Lithium Batteries

Room-temperature fabrication of garnet-type solid-electrolyte: Optimizing particle size for high ionic conductivity

Improving the Interfacial Contact between Li 7 La 3 Zr 2 O 12 and Lithium Anode by Depositing a Film of Silver

A novel thin solid electrolyte film and its application in all-solid-state battery at room temperature

Effects of H2O on Improving the Performance of a Solid Composite Electrolyte Fabricated via an Air-Processable Technique

Synthesis and Electrical Properties of Garnet-type Solid Oxide Electrolyte Thin Films from Solution Route

Reduced Energy Barrier for Li+ Transport Across Grain Boundaries with Amorphous Domains in LLZO Thin Films

Enhanced Performance of Li 6.4 La 3 Zr 1.4 Ta 0.6 O 12 Solid Electrolyte by the Regulation of Grain and Grain Boundary Phases

An integrated solvent-free modification and composite process of Li<sub>6.4</sub>La<sub>3</sub>Zr<sub>1.4</sub>Ta<sub>0.6</sub>O<sub>12</ sub>/Poly(ethylene oxide) solid electrolytes: Enhanced compatibility and cycle performance

Improving the Ionic Conductivity of the LLZO–LZO Thin Film through Indium Doping

Effects of Surfactants on Al2o3-Modified Li-Rich Layered Metal Oxide Cathode Materials for Advanced Li-Ion Batteries

The Synthesis and Application of Llzo Ultrathin Electrolyte Film

Improvement of the Energy Storage Performance in Pb0.88La0.12ZrO3 Thin Films by Inserting ZrO2 Layer

In Situ Formed Surface Layer to Improve the Air Stability of LLZTO and Its Contact with the Li Metal

Insight into Ion Diffusion Dynamics/Mechanisms and Electronic Structure of Highly Conductive Sodium-Rich Na 3+ x La x Zr 2– x Si 2 PO 12 (0 ≤ x ≤ 0.5) Solid-State Electrolytes