Abstract:Nano-sized aluminum (Nano-Al) powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time. However, the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear. In this study, the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics, detonation reaction zone, and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test, detonation pressure test, explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry. Lithium fluoride (LiF), which has an inert behavior during the explosion, was used as a control to compare the contribution of the reaction of aluminum. A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn. Combining the numerical simulations based on the calculated afterburn energy and experimental results, the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated. This study found that when the 170 nm Al content is from 0% to 15%, every 5% increase of aluminum resulted in about a 1.3% decrease in detonation velocity. Manganin pressure gauge measurement showed no significant enhancement in detonation pressure. The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm, which is respectively 14% and 8% higher than that of RDX/wax/95/5 explosive (57 ns and 0.39 mm). Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front. For the recording time of about 10 μs throughout the plate push test duration, the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12% and 2.9 μs higher than that of RDX/LiF/wax/80/15/5, respectively, indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive. Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume, over 80% of the aluminum had reacted, implying very high reactivity. These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.

Synthesis of nano-diamond/alumina composite by detonation method

Coating of diamond by thermal explosion reaction

Core–Shell Composites Based on Partially Oxidized Blend of Detonation Synthesis Nanodiamonds

Coating on the Surface of Diamond Particles by Thermal Explosion Reaction Method

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Detonation Synthesis Nanodiamond Soot as a Promising Filler for Polymer Composites

A Theoretical Insight for Nucleation of Diamond-like Carbon

Research on Composite Explosive with Nano-Aluminium

Preparation of NiAl2O4/Al2O3 composite nanopowder

Nano-Graphite Synthesized by Explosive Detonation and Its Application in Preparing Diamond under High-Pressure and High-Temperature

A simple and soft chemical deaggregation method producing single-digit detonation nanodiamonds

Influence of the Hierarchy Structure of Aluminum Particles on Density, Combustion Efficiency, and Ignition Delay

Reactive molecular dynamics simulation of thermal decomposition for nitromethane/nano-aluminum composites

Exploding wire preparation of core–shell aluminum–silicon nanoparticles and characterization as energetic material

Synthesis Of Nano-Nickel-Coated Micro-Aluminum And Thermal Reactivity Of Aluminum/Nickel-Stannic-Oxide Thermite

[Studies on nano-diamond prepared by explosive detonation by Raman and infrared spectroscopy]

Surface Functionalization and Structure Characterizations of Nanodiamond and Its Epoxy Based Nanocomposites

Characterization and Mechanism Elucidation of Nano-TiO2 Composites Prepared by Gaseous Detonation Method

Influence of Particle Size of Aluminum Powder and Morphology of Oxidizer in Rdx Based Aluminized Explosive on the Ability of Accelerating Metal (I)

The Physical-Mechanical Properties of Aluminum Nanocomposites Produced by High Energy Explosion Impact

Improved ignition and combustion performances of aluminum nanoparticles by in-situ partial conversion of native alumina to surface Al-MOF shell