Abstract:In this study, the effect of Cr content on microstructure and electrochemical measurement of low alloy steel in 3.5 wt% NaCl solution was investigated using scanning electron microscope (SEM), X-ray diffractometer (XRD), X-ray photoelectron spectroscopy (XPS) and electrochemical workstation, and the CCT curves of the samples were calculated using JMatPro software. The results showed that the augmentation of Cr content inhibits the formation of ferrite and promotes the development of cementite in low alloy steels. And the reduction of Ar3 (the temperature at which austenite transforms to ferrite) and the increase in Ar1 (the temperature at which ferrite transforms to pearlite) also contribute to the expansion of the pearlite area. The XRD results show that the samples primarily consist of Fe-Cr solid solution with a body-centered cubic structure. As the Cr content increases, the peaks corresponding to the (110), (200), and (211) planes gradually enhance which means the improvement in the crystallinity of the samples. The improvement in the crystallinity can result in a decrease of grain size. Due to the suitable ratio of cementite to pearlite and the synergistic effect of grain size refinement, the Cr2 sample exhibits the best tensile property when the Cr content is 0.970 wt%. Cr(OH)3 and Cr2O3 with protective effects are generated in the corrosion film on the surface of Cr-containing low-alloy steels. And Cr also promotes the transformation of γ-FeOOH to α-FeOOH in the corrosion film because of the atomic radius of Cr3+ being smaller than that of Fe3+. These substances enhance the ability of the corrosion film to block corrosive media and protect the matrix. The results of the electrochemical measurement showed that the increasing Cr content from 0.970 to 4.657 wt% resulted in the enhancement of steel's corrosion resistance. The Cr4 sample exhibits the best corrosion resistance when the Cr content is 4.657 wt%.

The Effects of Ball Milling Time and Surface Enriched Chromium on Microstructures and Corrosion Resistance of AISI 304 Stainless Steel

The Effect of Surface Enriched Chromium and Grain Refinement by Ball Milling on Corrosion Resistance of 316l Stainless Steel

Effect of Oxidation Time on the Structure and Properties of Ti-25Nb-3Zr-2Sn-3Mo Titanium Alloy Microarc Oxide Film Layer

Surface enriched molybdenum enhancing the corrosion resistance of 316L stainless steel

Effect of Carbon Content and Elements Mo and V on the Microstructure and Properties of Stainless Steel Powder Surfacing Layer

Effect of ball-milling time on the electrochemical performance of ball-milled LaMg11Ni+200wt% Ni composite

Effects of ball-milling time and Bi2O3 addition on electrochemical performance of ball-milled La2Mg17+200wt.% Ni composites

Effects of pack chromizing on the microstructure and anticorrosion properties of 316L stainless steel

Effect of chromium content on the erosion-corrosion behavior of Fe-Cr alloy produced by ball milling liner in weakly alkaline slurry

Effect of Milling Time on Powder's Structure Evolution of Ti(C,N)-304 Stainless Steel Cermet

Investigating the effect of Cr content on the microstructure and electrochemical measurement of low alloy steel

A High-Resolution Study of the Different Surface State Effects on the Corrosion Behaviors of a Ferritic Steel and an Austenitic Steel in Supercritical Water

Effects of Surface Machining by a Lathe on Microstructure of Near Surface Layer and Corrosion Behavior of SA182 Grade 304 Stainless Steel in Simulated Primary Water

The Effects of Grain Refinement and Deformation on Corrosion Resistance of Passive Film Formed on the Surface of 304 Stainless Steels

A Comprehensive Investigation on the Effects of Surface Finishing on the Resistance of Stainless Steel to Localized Corrosion

Electrochemical dissolution behavior of stainless steels with different metallographic phases and its effects on micro electrochemical machining performance

Effect of surface nanocrystallization induced by mechanical grinding treatment on stress corrosion cracking behavior of 316 L austenitic stainless steel in boiling MgCl 2 solution

Effect of Milling Time on the Microstructure and Mechanical Properties of Ti(C,N)-304 Stainless Steel Cermet

Effect of Ball Milling Time on the Microstructure and Properties of High-Silicon–Aluminum Composite

Corrosion behaviour of nanocrystalline 304 stainless steel prepared by equal channel angular pressing

The Grain Size and Special Boundary Dependence of Corrosion Resistance in 304 Austenitic Stainless Steels