Abstract:3D‐compliant thermoelectric generators (TEGs) fabricated solely by direct ink writing through out‐of‐plane printing of viscoelastic carbon nanotube‐based thermoelectric (TE) inks are proposed. By optimizing 3D structural design and doped printable TE materials, TEGs exhibit the highest TE performance among printed TEGs and outstanding mechanical reliability. Compliant thermoelectric generators (TEGs) can fully exploit their energy conversion efficiency by establishing conformal interfaces on arbitrarily shaped 3D heat sources. Although additive manufacturing processes allow scalable fabrication with flexibility and customizability, most printable TEGs are fabricated as planar‐type devices that harvest heat only in the in‐plane direction. Herein, 3D‐compliant TEGs fabricated solely using direct ink writing, which enables thermal‐transfer optimization for efficient through‐plane heat‐to‐electricity conversion owing to the out‐of‐plane printing of viscoelastic thermoelectric (TE) inks and unique device design is proposed. The rheological properties of carbon nanotube (CNT) TE inks are engineered to ensure conformal printing along directly written vertical thermal insulators. The ink TE properties are enhanced by the fine‐tuned incorporation of p‐ and n‐type dopants, where the electrical conductivity is further facilitated by nozzle‐induced CNT packing to achieve high‐power factors. To minimize the parasitic thermal loss from heat sources, an ultra‐thin bottom substrate is directly printed with polydimethylsiloxane, thereby realizing compliant 3D TEGs for heat harvesting in the out‐of‐plane direction. The TEG exhibits the highest normalized open‐circuit voltage (0.28 mV K−1 cm−2) among the additively manufactured TEGs and retains remarkable mechanical reliability against repetitive deformation, promising its potential as body heat harvesters or temperature sensors.

Inkjet Printing of Single‐Crystalline Bi2Te3 Thermoelectric Nanowire Networks

Inkjet Printing Flexible Thermoelectric Devices Using Metal Chalcogenide Nanowires

Direct ink writing of high-performance Bi2Te3-based thermoelectric materials by quasi-inorganic inks and interface engineering

Fabrication of Bi<sub>2</sub>Te<sub>3</sub> Nanowires Applied in Thermoelectric Generators

Templating Synthesis Of Uniform Bi2te3 Nanowires With High Aspect Ratio In Triethylene Glycol (Teg) And Their Thermoelectric Performance

Fabrication of Bi2te3 Nanowires Applied in Thermoelectric Generators

Rational synthesis of ultrathin n-type Bi2Te3 nanowires with enhanced thermoelectric properties

High performance thermoelectric composites via scalable and low-cost ink processing

Direct ink writing of Bi2Te3-based thermoelectric materials induced by rheological design

3D Printing of Bi2Te3-Based Thermoelectric Materials with High Performance and Shape Controllability

Stencil-Printed Scalable Radial Thermoelectric Device Using Sustainable Manufacturing Methods

Enhanced Thermoelectric Properties of Bi2 Te3 -Based Micro-Nano Fibers Via Thermal Drawing and Interfacial Engineering.

All Direct Ink Writing of 3D Compliant Carbon Thermoelectric Generators for High‐Energy Conversion Efficiency

Bi2te3 Nanowire Array Preparation and Surface Polishing by Electrochemical Deposition

High-performance and flexible thermoelectric films by screen printing solution-processed nanoplate crystals

Development of Nanostructured Bi2Te3 with High Thermoelectric Performance by Scalable Synthesis and Microstructure Manipulations

Thermoelectric Nanowires for Dense 3D Printed Architectures

Enhanced Thermoelectric Properties of Bi2Te3‐based Micro‐nano Fibers Via Thermal Drawing and Interfacial Engineering

Broad Temperature Plateau for High Thermoelectric Properties of n-Type Bi 2 Te 2.7 Se 0.3 by 3D Printing-Driven Defect Engineering

A simple thermoelectric device based on inorganic/organic composite thin film for energy harvesting

Carbon Nanotube Ink Dispersed by Chitin Nanocrystals for Thermoelectric Converter for Self‐Powering Multifunctional Wearable Electronics