Abstract:The use of titanium (Ti) in the additive manufacturing (AM) industry has been steadily increasing. However, iron (Fe), a significant impurity originating from the sponge production process, is difficult to remove due to high energy requirements. Consequently, fully eliminating Fe from Ti is challenging and expensive. Understanding the role of Fe in Ti alloys and determining a maximum allowable threshold for AM is therefore critical. This knowledge could potentially relax current industry standards and enable the development of more sustainable Ti alloys. This study investigated the effect of Fe on the microstructure development and mechanical properties of Ti-Fe alloys, with a focus on their suitability for additive manufacturing. Through an in-situ alloying approach, Fe content was systematically increased from 0 to 3 wt%, leading to significant grain size reduction, from over 100 μm to less than 5 μm. These modifications in grain size and morphology, achieved by adjusting the Fe content in laser-based powder bed fusion (LPBF) fabricated Ti alloys, are directly related to substantial enhancements in the mechanical properties. The hardness increased from 171 to 366 HV, and the tensile strength effectively doubled from 426 to 1026 MPa while maintaining ductility. XRD analysis revealed the presence of a full α phase when the Fe content was ≤ 0.75 wt%. However, at higher Fe concentrations, small β peaks were observed. To identify the strengthening mechanisms, theoretical frameworks such as the Hall-Petch relationship and Labusch model were employed. Two significant inflection points were identified at Fe concentrations of 0.1 % and 1 wt%, indicating three important compositional ranges: Region #1 (Fe ≤ 0.1 wt%), Region #2 (0.1–1 wt% Fe), and Region #3 (1–3 wt% Fe). The strengthening mechanism in each region is discussed in detail.

Fabrication of Low-Cost Ti-1Al-8V-5Fe by Powder Metallurgy with TiH2 and FeV80 Alloy

Effects of Sintering Temperature and Holding Time on Microstructure and Mechanical Properties of Ti−1Al−8V−5Fe Prepared by Spark Plasma Sintering

Cost-affordable Ti-6Al-4V for Additive Manufacturing: Powder Modification, Compositional Modulation and Laser In-Situ Alloying

Microstructure, mechanical properties and corrosion resistance of low-cost Ti–Al–Cr–Fe alloys processed via powder metallurgy

Behaviour of novel low-cost blended elemental Ti-5Fe-xAl alloys fabricated via powder metallurgy

Pre-hydrogenation metallurgy for Ti-3Al-5Mo-4.5V alloy with high density and mechanical properties

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

A Study of the Superplastic Deformation Behavior of Low-Cost Ti-2Fe-0.1B Alloys

Development of a Low-Density and High-Strength Titanium Alloy

Investigating phase transformation, densification and diffusion mechanism of TiH 2 powder to achieve a high ductile Ti6Al4V alloy

Microstructual evolution in Ti-185 alloy prepared using electrostatic levitation and conventional casting techniques

Microstructures and mechanical properties of high strength Ti-XAl-2Fe-3Cu alloys fabricated by powder compact extrusion

Fabrication of Ti3Al-Based Intermetallic Alloy by Laser Powder Bed Fusion Using a Powder Mixture

Integrated high-performance and accurate shaping technology of low-cost powder metallurgy titanium alloys: A comprehensive review

Design of Low-Cost and High-Strength Titanium Alloys Using Pseudo-Spinodal Mechanism through Diffusion Couple Technology and CALPHAD

The Effect of Heat Treatment on the Microstructure and Mechanical Properties of the Novel Low-Cost Ti-3Al-5Mo-4Cr-2Zr-1Fe Alloy

A Cost-Efficient Fabrication Strategy for Conductive Ti2alc Honeycomb Monolith Using Elemental Powders

Sustainable alloy design: Fe-enhanced Ti alloys for superior mechanical performance in additive manufacturing

Precise fabrication of Ti2O from TiO2 by Al reduction towards potentially lower-cost Ti metal powder production

Mechanical Properties and Microstructure of Fe40al/Tic Composites with Low Content of Intermetallic

The microstructure and mechanical properties of extra low interstitials (ELI) Ti-6Al-4V alloys manufactured from hydride–dehydride (HDH) powder