Abstract:Microwave communication systems are being developed with the goal to achieve miniaturization and high reliability. There are urgent requirements for microwave dielectric materials to exhibit low sintering temperatures, excellent microwave dielectric properties, and prominent mechanical performance. However, simultaneously achieving these requirements is a significant challenge. These concerns have been addressed in the uniform ultrafine-grained 0.95MgTiO(3)-0.05CaTiO(3) ceramics with an average grain size of similar to 0.5 mu m via a grain size engineering strategy. Interestingly, the sintering temperature in the unique two-step sintering method of 1250celcius/1 min and 1130celcius/10 h is much lower (200-300celcius) than that obtained in the conventional sintering method reported previously (1400-1450celcius). Excellent dielectric properties are achieved, with relative permittivity epsilon(r) = 20.11, quality factor Q x f = 68 613 GHz, and temperature coefficient of resonant frequency tau(f) = 1.81 ppm/celcius. The bending strength sigma f, Vickers hardness H-v, and elastic modulus E reach up to 212.4 MPa, 10.1 GPa, and 200.7 GPa, respectively. These values are significantly enhanced over those of samples obtained via the conventional sintering method with an average grain size of similar to 2.5 mu m. For the first time, uniform ultrafine-grained microwave dielectric materials with excellent microwave dielectric properties and prominent mechanical performance were synthesized. This work provides a guideline for developing other high-performance microwave dielectric materials and makes a significant contribution to the miniaturization and high reliability of microwave dielectric devices.

The Dielectric Constant and Quality Factor Calculation of the Microwave Dielectric Ceramic Solid Solutions

FEM Simulation of Dielectric Properties of Composite Ceramics

Maxwell–Wagner Polarization in Ceramic Composites BaTiO3–(Ni0.3Zn0.7)Fe2.1O4

MIXTURE EFFECTIVE PERMITTIVITY SIMULATIONS USING IMLMQRF METHOD ON PRECONDITIONED EFIE

FEM Simulation of Microwave Dielectric Properties for Biphase Ceramics

High quality factor microwave dielectric ceramics in the (Mg<sub>1/3</sub> Nb<sub>2/3</sub> )O<sub>2</sub> -ZrO<sub>2</sub> -TiO<sub>2</sub> ternary system

Microwave Dielectric Ceramics and Devices for Wireless Technologies

Measurement of Dielectric Constant of Thin Film Materials at Microwave Frequencies

High quality factor microwave dielectric ceramics in the (Mg1/3Nb2/3)O2–ZrO2–TiO2 ternary system

Microwave dielectric ceramics (1 x)ZnNb2O6 xZnTa2O6 with high quality factors

Coordinated Modification Of Microstructures And Properties In Ba6-3xnd8+2xti18o54 Microwave Dielectric Ceramics

A Microwave Dielectric Ceramic with Ultra-low Dielectric Constant Prepared by Reaction Sintering Method

Three‐phase borate solid solution with low sintering temperature, high‐quality factor, and low dielectric constant

The Dielectric Constant of Ba6-3 x(Sm1- yNdy)8+2 xTi18O54 (x = 2/3) Ceramics for Microwave Communication by Linear Regression Analysis

Structure and properties of (Mg0.4Zn0.6)2SiO4 microwave dielectric ceramics based on first-principles calculations

Near-zero Temperature Coefficient in Mg2+–Ti4+ Co-Doped Sm2O3–CaSmAlO4 Microwave Dielectric Ceramics

SrZnV 2 O 7 : A low‐firing microwave dielectric ceramic with high‐quality factor

Grain Size Engineered 0.95mgtio3–0.05catio3 Ceramics with Excellent Microwave Dielectric Properties and Prominent Mechanical Performance

Microwave dielectric properties and sintering behaviors of Zn1.8SiO3.8 ceramics

Numerical Analyses of Effective Dielectric Constant of Multiphase Microporous Media

Microwave Dielectric Properties of (0.75znal2o4–0.25tio2)–mgtio3 Ceramics Prepared Using Digital Light Processing Technology