Abstract:The nature of the interface between ceramic particle (CP) and metal matrix is critical to obtain solidification microstructures with optimal mechanical properties of CP-reinforced Al alloys in additive manufacturing. Generally, when the lattice misfit between the CP (e.g., TiB2) and the alpha-Al matrix is higher than 4%, the interfacial coherency reduces, lowering the effectiveness of CPs. Here, we demonstrate that an L12 three-dimensional compound (3DC), which possesses lattice misfit with alpha-Al lower than 1%, can be introduced in between TiB2 and alpha-Al via properly regulating the solidification cooling rate. In the 5TiB2/Al-4.5Mg-0.7Sc-0.2Zr (wt%) as a model system, the lattice coherence of the TiB2/alpha-Al interface is tailored by introducing a 10-30 nm thick Al3(Sc,Zr) 3DC interphase when the cooling rate is increased to-1000 degrees C/s. But, further increasing the cooling rate to-6800 degrees C/s, only Al3(Sc,Zr) two-dimensional compound (2DC) with an apparent lattice strain forms at the interface. Taking advantage of the cooling rate (102-103 oC/s) provided by laser direct energy deposition (L-DED), the low-misfit "TiB2/Al3(Sc,Zr) 3DC/alpha-Al" multi-structural interfaces are acquired, enabling the 3.56TiB2/Al-4.36Mg-0.72Sc-0.22Zr alloy as fabricated with L-DED to achieved improved strength-ductility synergy (yield strength 257 MPa, elongation 13.8%) due to the isotropically fine Al grain structure and the homogenous TiB2 particle dispersion. The outcome of this study provides fundamental knowledge on designing "ceramic/coherent primary interphase/metal matrix" multi-structural interfaces to improve the mechanical properties of engineering metallic materials manufactured by rapid solidification techniques, such as DED additive manufacturing (AM).

Manufacturing of High Volume Fraction of Ti3AlC2-Ti2AlC Metallic Ceramics As Nano-Multilayered Structures Through High Energy Milling, Hot Pressing and Liquid Phase Sintering

Synthesis and microstructure of layered-ternary Ti2AlC ceramic by high energy milling and hot pressing

Manufacturing a TiAl Alloy by High-Energy Ball Milling and Subsequent Reactive Sintering

Manufacturing Titanium Metal Matrix Composites by Consolidating Matrix Coated Fibres

SYNTHESIS OF NANOSTRUCTURED GAMMA-TiAl BASED POWDERS AND BULK ALLOYS USING HIGH ENERGY MECHANICAL MILLING AND HIP

Synthesis of Tial Based Alloy by Mechanical Milling, Warm Pressing and Reactive Sintering

Synthesis of Ti2alc/Al2o3 Nanocomposites by High Energy Milling and Heat Treatment

Microstructure and Properties of A Tial Alloy Prepared by Mechanical Milling and Subsequent Reactive Sintering

Preparation of Ti-45Al-5.5(Cr,Nb,B,Ta) Alloy by Mechanical Milling and Spark Plasma Sintering

Nanoscale Engineering of Low-Misfit TiB2/Al3(Sc,Zr)/α-Al Multi-Interface to Improve Strength-Ductility Synergy for Direct Energy Deposited Aluminum Alloy

Effect of Milling Parameters on the Development of a Nanostructured FCC–TiNb15Mn Alloy via High-Energy Ball Milling

Nanoscale engineering of low-misfit TiB 2 /Al 3 (Sc,Zr)/α-Al multi-interface to improve strength-ductility synergy for direct energy deposited aluminum alloy

Synthesis of Ti3AlC2 Powder by High Energy Ball Milling and High Temperature Heat Treatment

Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting

Mechanical Properties of (ti2alc+ti3alc)–tial Ceramic–intermetallic Laminate (CIL) Composites

Preparation of TiAl-based alloys by mechanical milling and reactive sintering

Structural and thermal properties of the Fe-based alloys prepared by mechanical milling

Synthesis, characterization, and mechanical behavior of ultra-fine-grained Ti-6Al-5V alloy prepared by mechanical alloying and spark plasma sintering

Mechanical Alloying and Spark Plasma Sintering of Ni-Al-Ti-B Powders for Fabricating Nanocrystailine (Tib+tib2)/ni-3(Al, Ti) Composite

Additive manufacturing of fine-grain fully lamellar titanium aluminide alloys

Synthesis and Properties of an Ultrafine Grained Ti-45al-2cr-2nb-1b-0.5ta Alloy Prepared by Double Mechanical Milling and Spark Plasma Sintering