Abstract:The substrate of as-cast Ni-28 wt% Sn hypoeutectic alloy immersed in liquid nitrogen is rapidly remolten and solidified by laser surface remelting with a scanning velocity of 10 mm/s and the laser power of 1950 W. The microstructure of the substrate and its effect on the microstructure of the molten pool are investigated by scanning electron microscope carefully. It is found that the substrate of the Ni-28 wt%Sn ingot is composed of coarse primary α-Ni dendrites and the interdendritic (α-Ni+Ni3Sn) eutectic. The growth orientations of α-Ni dendrites and the interdendritic eutectic are distributed nearly randomly in the as-cast substrate. There are three kinds of microstructure characterstic zones from the top to the bottom of melted pool. The growth directions of α-Ni dendrites with the primary dendritic spacings ranging from 4.19 to 6.91 μm are approximately parallel to the laser scanning direction at the top of the molten pool due to the fact that the temperature gradient at the interface between the molten pool and substrate tends to be parallel to the laser scanning direction. In the middle of the molten pool, the epitaxial α-Ni columnar dendrites are found to be inclined to grow in the direction vertical to the bottom of the molten pool due to the fact that the temperature gradients in most zones of the molten pool are perpendicular to the bottom of the molten pool. The formation of new primary dendrites by the growth of the tertiary arm results in the decrease of primary dendritic spacing in comparison with that at the bottom of the molten pool. There are a small quantity of residual α-Ni primary phase and a large amount of (α-Ni+Ni3Sn) eutectic at the bottom of the molten pool. The microstructure of laser remolten zone is greatly influenced by the substrate microstructure, and the growth direction of the α-Ni dendrite in the molten pool is also affected remarkably by both the heat flux and the preferred crystal orientations for dendritic growth. Compared with the mixed lamella, rod and divorced (α-Ni+Ni3Sn) eutectic microstructures in the substrate, the eutectic structure in the molten pool is completely composed of the refined lamellar eutectic, which grows epitaxially in the direction perpendicular to the interface between the molten pool and the substrate at the bottom of molten pool. The eutectic lamellar spacing increases from the top (0.23 μm± 0.01 μm) to the bottom (0.42 μm± 0.02 μm) of the molten pool due to the interface growth velocity decreasing from the top to the bottom. The Kurz-Giovanola-Trivedi model for rapid dendritic growth and the Trivedi-Magnin-Kurz model for eutectic growth are used to estimate the growth undercooling of the microstructure in the molten pool respectively. It is found that the growth undercooling of dendrites and the eutectic in the molten pool should be between 50.4 K and 112.5 K, which is much larger than the critical undercooling for anomalous eutectic growth found in the high undercooled solidification in the previous researches. This phenomenon means that the critical undercooling for anomalous eutectic growth reported in the previous literature may be not the sufficient condition for generating the anomalous eutectic.

Regular Eutectic and Anomalous Eutectic Growth Behavior in Laser Remelting of Ni-30wt%Sn Alloys

Microstructure Evolution in Laser Surface Remelting of Ni–33wt.%Sn Alloy

Three-dimensional reconstruction of anomalous eutectic in laser remelted Ni-30 wt.% Sn alloy.

Numerical Simulation of Anomalous Eutectic Growth of Ni-Sn Alloy under Laser Remelting of Powder Bed

Primary Phase Growth Within Highly Undercooled Cu-Ge Eutectic Alloys

Microstructural Evolution of Laser Surface Remelting Ni-28 Wt% Sn Alloy under Liquid Nitrogen Cooling

Microstructure Evolution of Ni-33％Sn Hypereutectic Alloy in Laser Rapid Solidification

Formation of Anomalous Eutectic in Ni-Sn Alloy by Laser Cladding

Microstructure Evolution of Ni-Sn Eutectic Alloy in Laser Cladding

Cellular Automaton Simulation of the Growth of Anomalous Eutectic During Laser Remelting Process

Influence of Γ/γ′ Morphology Evolution on the Mechanical Properties of Ni-based Single Crystal Superalloys Formed by Laser Metal Deposition

In Situ Observation of Remelting Induced Anomalous Eutectic Structure Formation in an Undercooled Ni-18.7 At.% Sn Eutectic Alloy

Research on the Melt Pool Shape Formation Mechanism of the Laser Surface Remelting of Nickel-Based Single-Crystal Superalloy

Growth mechanisms of dendrites and eutectics within undercooled liquid Al-Ni alloys

The Formation Mechanism of Anomalous Eutectic in Highly Undercooled Ni-Sn Eutectic Alloy

Microstructural Characteristics of Ni-Sb Eutectic Alloys under Substantial Undercooling and Containerless Solidification Conditions

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

Epitaxial growth behavior and stray grains formation mechanism during laser surface re-melting of directionally solidified nickel-based superalloys

Influences of Laser Remelting Treatments on Microstructure and Tensile Properties of Multiphase Ni3Al-based Intermetallic Alloy

Globular to Lamellar Transition During Anomalous Eutectic Growth

Phase and Microstructure Pattern Selection of Zn-rich Zn–Cu Peritectic Alloys During Laser Surface Remelting