Abstract:Accurately evaluating the simple shear in sheet metals has proven to be challenging owing to three reasons: a) the detailed shear strain evaluation is different from one publication to another; b) the measured strain is strongly dependent on the employed virtual strain gauge size (LVSG) when digital image correlation (DIC) is utilized; and c) the negligence of the strain perturbation phenomenon (Swift effects) will only result in a rough estimation of the strain–stress behavior. Thus, in this study, a finite strain perturbation analysis according to the configuration of experimental tests was constructed to understand the shear strain–stress evolution, and a high-resolution quasi-in-situ strain measurement technology was developed to capture the localized shear strain with reliable results. Material anisotropy and simple shear specimen geometry were identified as the two major contributors to the Swift effects. Hence, a finite strain perturbed shear kinematics was first proposed, revealing that some specific shear strain estimations led to a certain degree of error (∼12–25%) at large deformation levels. This work demonstrated that the finite element simulation of simple shear tests, performed using the carefully calibrated YLD2004 yield model, can be utilized to reasonably predict perturbation. A Vickers-indentation-based quasi-in-situ strain measurement was further developed to obtain reliable local strain of the shear zone with LVSG =28 μm. The technique was found to provide high-resolution strain detection to satisfy the necessary conditions of accurate strain measurement when a narrow shear band is present. The results yielded a 30% higher von Mises strain under simple shear deformation than that reported in previous publications for a similar DP980 sheet. The said result was also found to be larger than the fracture strain determined through the so-called “hybrid method”. The proposed perturbed shear kinematics was further implemented in the anisotropic elastoplasticity framework to show that the magnitude of normal stresses did not always remain in the second order with respect to the shear stress due to strain perturbation. Thus, the concept of “perturbed” shear stress was designed to consider the effects of perturbation, and the findings signified a 6–13% change in shear stress compared with the commonly used shear stress for tested scenarios.

New Formulas of Shear Strain During Equal-channel Angular Pressing Process with Consideration of Influences of Velocity and Motion Trajectory

Tensile and Compressive Deformation Behaviors of Commercially Pure Al Processed by Equal-Channel Angular Pressing with Different Dies

Tensile Deformation Behaviors of CuNi Alloy Processed by Equal Channel Angular Pressing

Reducing the Tension–compression Yield Asymmetry of Extruded Mg–Zn–Ca Alloy Via Equal Channel Angular Pressing

Influence of equal channel angular pressing in an acute angle die with a back pressure notch on grain refinement, torsion and mechanical properties of aluminium

Deformation mechanism finite element analysis and die geometry optimization of magnesium alloys by equal channel angular processing

Simulation And Experimental Investigation For The Homogeneity Of Ti49.2ni50.8 Alloy Processed By Equal Channel Angular Pressing

Research on incremental forming simulation based on an improved constitutive model

Simple shear deformation of sheet metals: finite strain perturbation analysis and high-resolution quasi-in-situ strain measurement

Study on equal channel angular pressing process of Mg–Zn–Y–Mn–Ti magnesium alloy enhanced by lamellar LPSO phase and spherical W phase

Effect of equal channel angular extrusion process on deformation behaviors of Mg-3Al-Zn alloy

Tailoring Deformation Homogeneity of WE43 Alloy through Strain Rate Sensitivity and Back Pressure during Equal Channel Angular Pressing

Orientation factor analysis of deformation mechanisms under special processing techniques in AZ31 magnesium alloys

The central strain analytical modeling and analysis for the plate rolling process

A Novel Method for Friction Coefficient Calculation in Metal Sheet Forming of Axis-Symmetric Deep Drawing Parts

Push-bending Process of Stainless-Steel Tubes: Experiment and Simulation

Finite element analysis and die project of Twist Equal-Channel Angular Pressing (T-ECAP) using pure Cu and CuCrZr alloy

Testing, modelling and design of hot-rolled stainless steel channel sections under combined compression and minor-axis bending moment

Analysis of stress-strain in the partial heating roll forming process of high strength square hollow steel sections

The Study and Application on Ductile Fracture Criterion of Dual Phase Steels During Forming

A constitutive model on flow stress prediction from the contribution of twin and grain refinement, strain and strain rate during surface mechanical attrition treatment of metals