Abstract:The steel plate shear walls (SPSWs) have been proven effective in reinforced concrete frames (RCFs) as a lateral force‐resistant structure. Despite of advancements, accurately predicting the ultimate shear capacity of RCFs with SPSWs remains challenging using current simplified models. Additionally, the flexural capacity design procedure for the boundary elements (beams and columns) in previous studies of RCF‐SPSWs involved intricate iterative procedures, hindering its widespread implementation. To address the two issues, this paper investigates the pushover responses and the plate‐frame interaction (PFI) of an RCF‐SPSWs system using theoretical and numerical methods. There are three main contributions. First, a theoretical model of ultimate shear capacity for RCF‐SPSWs is proposed, which can also be used to predict shear contributions of boundary frames in RCF‐SPSWs. Calculation errors for ultimate shear capacity of RCF‐SPSWs and shear contribution from the boundary frame are only 3.7% and 6.7% respectively, which are reduced dramatically compared with the traditional model. A simplified schematic diagram for the global collapse mechanism (uniform distribution of plastic hinges within a structure) of RCF‐SPSWs is developed to facilitate the calculation of internal work and reaction forces. Secondly, a flexural capacity design method for the boundary elements to avoid in‐span plastic hinges is proposed. The proposed method enables the achievement of direct estimation of the flexural demands that could trigger a global collapse mechanism, all without intricate iterative procedures. The applicability of current assumptions for the design of steel boundary frame in RCF‐SPSWs system is discussed, and engineering suggestions are provided to ensure safer and more economic designs. Comparison results confirmed the applicability of the proposed design method, which can be adopted to achieve the global collapse mechanism for RCF‐SPSW system. Thirdly, impacts of yielding panel actions on the flexural capacity of boundary elements of RCF‐SPSWs are clarified. Comparison results demonstrated that adding SPSWs to an RCF alters the axial force on boundary elements and significantly impacts the flexural capacity. A design suggestion is made to emphasize the importance of avoiding the balanced failure of boundary elements. The proposed theoretical model can be used to economize the cross‐section of boundary elements in RCF‐SPSWs system under seismic loads due to accurate prediction of their shear contribution; the proposed flexural capacity design method can achieve a global collapse mechanism, and thus the structural safety and energy dissipation capacity are improved; moreover, the building design efficiency is also improved due to avoidance of intricate iterative procedures.

Higher Mode Effects in Frame Pin‐supported Wall Structure by Using a Distributed Parameter Model

A Distributed Parameter Model of Frame Pin-Supported Wall Structure

A distributed parameter model of a frame pin‐supported wall structure

Experimental study and numerical simulation of seismic performance of stiffened thin steel plate shear walls considering the effect of vertical load on frame column

Study on the RC Frame with the Partial Infill Wall in Pushover Analysis

Analytical Model for Steel Frame-Reinforced Concrete Infill Slit Wall System

Determination of buckling mode for elastic-plastic braced frames

Shear transfer mechanism of a multi-storied structural wall under the cyclic lateral load: experiment and detachment model

Evaluation of Modal and Traditional Pushover Analyses in Frame-Shear-Wall Structures

Elasto-Plastic Seismic Shear Distributions of Frame-Wall Structures

Seismic behavior of multi-story structural walls under cyclic lateral loading: Experimental study

Seismic performance evaluation of an infilled rocking wall frame structure through quasi-static cyclic testing

A cantilever beam analogy for quantifying higher mode effects in multistorey buildings

Performance analysis of rocking shear wall‐frame structure

Numerical Analysis Study on Seismic Performance of Semi-Rigid Steel Frame Infilled with Prefabricated Composite Wall Panels

Distribution mode of hysteretic energy and damage mechanism of RC frame-shear-wall structure under strong earthquakes

Seismic performance of wall plate supported semi-rigid steel frames with a novel type of wall-beam connector

Experimental study of the hysteretic behavior of prefabricated frame-shear wall structures with grouting sleeve connections

STUDY ON MECHANICAL PROPERTIES OF SIMPLIFIED STEEL FRAME MODEL WITH EXTERNAL WALL PANELS

Theoretical model of ultimate shear capacity and flexural capacity design method of boundary elements for reinforced concrete frames with steel plate shear walls

Experiments and Numerical Simulations on the Seismic Performance of Steel-Frame Composite Wallboard Shear Walls