Abstract:Solid oxide fuel cell (SOFC) provides a new method for clean and efficient conversion and utilization of hydrocarbon fuels due to its high fuel flexibility. The utilization of biogas fuel through direct internal reforming (DIR) allows for a simplification of the SOFC system since no external reformer appears strictly necessary. Despite its considerable convenience and potential, at present, direct internal dry reforming is still not considered as a competitive process for commercial application, which is limited by the reaction difficulty and high risk of carbon deposition. To address the problem, in this study, conventional Ni-yttrium stabilized zirconia (YSZ) anodes of SOFCs are modified by two methods, i.e. Ce0.9Gd0.1O2-δ (GDC) infiltration and a Ni-GDC reforming catalytic layer. A comparative study between the modified cells and the bare cell is made under operation with humidified H2 and simulated biogas. Both of these two modification methods lead to a slight but acceptable decrease of the cell performance under humidified H2. In the case of simulated biogas, results show that GDC infiltration is only beneficial to the cell performance with very low or very high CO2/CH4 molar ratio. While with a moderate CO2/CH4 ratio of 0.5–1.5, GDC infiltration instead results in a decrease of cell performance. However, the cell modified by a Ni-GDC catalytic layer shows superior performance towards the direct utilization of simulated biogas than the bare one and the one modified by GDC infiltration. The anode modification by a Ni-GDC catalytic layer can also improve the stability of the cell under simulated biogas, which is verified under different operating currents, although serious carbon deposition is detected in the catalytic layer afterwards.

Biomass Integrated Gasifier-Fuel Cells: Experimental Investigation on Wood Syngas Tars Impact on NiYSZ-anode Solid Oxide Fuel Cells

Techno-Environmental Analysis of the Use of Green Hydrogen for Cogeneration from the Gasification of Wood and Fuel Cell

Tar Removal from Biomass-Derived Fuel Gas by Pulsed Corona Discharges

The effect of heavy tars (toluene and naphthalene) on the electrochemical performance of an anode-supported SOFC running on bio-syngas

Biomass Steam Gasification, High-Temperature Gas Cleaning, and SOFC Model: A Parametric Analysis

Synergic Effects of Bed Materials and Catalytic Filter Candle for the Conversion of Tar during Biomass Steam Gasification

Applicability of the SOFC technology for coupling with biomass-gasifier systems: Short- and long-term experimental study on SOFC performance and degradation behaviour

A Strategy To Reduce The Impact Of Tar On A Ni-Ysz Anode Of Solid Oxide Fuel Cells

Solid Oxide Fuel Cells Fueled by Simulated Biogas: Comparison of Anode Modification by Infiltration and Reforming Catalytic Layer

In-situ electrochemical impedance analysis of a commercial SOFC stack fueled by real wood gas

Biomass integrated gasification–SOFC systems: Technology overview

Syngas conditioning by ceramic filter candles filled with catalyst pellets and placed inside the freeboard of a fluidized bed steam gasifier

A strategy to reduce the impact of tar on a <scp>Ni</scp> ‐ <scp>YSZ</scp> anode of solid oxide fuel cells

Multi-physics field modeling of biomass gasification syngas fueled solid oxide fuel cell

Integrated plasma gasification and SOFC system simulation using Aspen Plus

Controlled Deposition and Utilization of Carbon on Ni-Ysz Anodes of Sofcs Operating on Dry Methane

Experimental Investigation of Naphthalene Induced Degradation of Reversible Solid Oxide Cells Operated on Bio-Syngas

Surface-engineered ceramic anode with asymmetric microchannels for efficient power and syngas co-generation in solid oxide fuel cells

A review on biomass derived syngas for SOFC based combined heat and power application

Biogas from the organic fraction of municipal solid waste: dealing with contaminants for a solid oxide fuel cell energy generator

Biogas-Fueled Flame Fuel Cell for Micro-Combined Heat and Power System