Abstract:Carbon nanotube/continuous carbon fiber reinforced poly(ethylene terephthalate) (CNT/CCF/PET) composites are prepared by melt impregnating. The effects of CF and CNT content on the mechanical properties, melt and crystallization behaviors, and submicroscopic morphology of CNT/CCF/PET composites are studied. The tensile test results show that the increase of CF and the addition of appropriate amount of CNT improved the tensile strength and tensile modulus of the composites. When the content of CNT is 1.0 wt% and the content of CF is 56 wt%, the properties of the composites are the best, with tensile strength of 1728.7 MPa and tensile modulus of 25.1 GPa, which is much higher than that of traditional resin matrix composites. The results of dynamic mechanical analysis (DMA) show that the storage modulus of the composites increased with the increase of CF and CNT content. In particular, the addition of CNT greatly reduced the loss modulus of the composites. Morphological analysis show that the addition of CNT improved the fiber–matrix interface of the composite, which changes from fiber pull-out and fracture failure to fiber matrix fracture failure, and the fiber matrix interface is firmly bonded. In addition, there are polymer coated CNT protrusions on the surface of the fiber was observed. The results of differential scanning calorimetry (DSC) show that the melting temperature and crystallization temperature of the composites increased with the increase of CF content. The addition of CNT had little effect on the melting temperature of the composites, but it further improved the crystallization temperature of the composites. The effect of CNT content on the crystallization kinetics of the composites is studied. The non-isothermal crystallization kinetics of the composites is described by Jeziorny's improved Avrami equation. The results show that CNT has a great influence on the crystallization type of the composites. As a nucleating agent, CNT has obvious heterogeneous nucleation effect in the composites, which improves the crystallization rate of PET.

Microstructures and Flexural Properties of C/C Composites Doped with CNTs by Electrophoretic Deposition

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

Reducing Dispersity of Mechanical Properties of Carbon Fiber/epoxy Composites by Introducing Multi-Walled Carbon Nanotubes

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Preparation and Damping Properties of Cups-Stacked Carbon Nanotubes(Cscnts)/Prime 20

Tribological properties of carbon nanotube-doped carbon/carbon composites

Effects of the Electrophoretic Deposition of CNTs on the Mechanical Properties of Ti/CFRP Composite Laminates

A Novel Continuous Carbon Nanotube Fiber/carbon Composite by Electrified Preform Heating Chemical Vapor Infiltration

Tensile Mechanical Behaviors of High Loading of Carbon Nanotube/Epoxy Composites via Experimental and Finite Element Analysis

Epitaxial Grown Carbon Nanotubes Reinforced Pyrocarbon Matrix in C/C Composites with Improved Mechanical Properties

Carbon fiber/epoxy composite property enhancement through incorporation of carbon nanotubes at the fiber-matrix interphase – Part II: Mechanical and electrical properties of carbon nanotube coated carbon fiber composites

Design and Preparation of CNTs/Mg Layered Composites

Microstructure of Carbon Nanotubes/pet Conductive Composites Fibers and Their Properties

The effect of carbon nanotubes on the microstructure and morphology of pyrolytic carbon matrices of C–C composites obtained by CVI

Fabrication and mechanical properties of in situ prepared mesocarbon microbead/carbon nanotube composites

Effectiveness of short and straight carbon nanotubes on dispersion state and static/dynamic mechanical properties of woven glass fibre-reinforced polymer laminates

Improving thermal shock and ablation resistance of high thermal conductivity carbon/carbon composites by introducing carbon nanotubes

Achieving high ductility in layered carbon nanotube/copper composite prepared by composite electrodeposition

High-strength and toughness carbon nanotube fiber/resin composites by controllable wet-stretching and stepped pressing

Mechanical Properties, Melting and Crystallization Behaviors, and Morphology of Carbon Nanotubes/Continuous Carbon Fiber Reinforced Polyethylene Terephthalate Composites

Preparation and Properties of Carbon Fiber/Carbon Nanotube Wet-Laid Composites