Abstract:Interfacial engineering is critical for highly efficient charge carrier transport in perovskite solar cells (PSCs). Herein, we developed a new method, called successive surface engineering, that affords PSCs with enhanced efficiency and dramatically suppressed current-voltage hysteresis. Upon modifying the TiO2 compact layer, which is commonly used as an electron transport layer (ETL) in regular-structure (n-i-p) planar heterojunction (PHJ) PSCs, by successively incorporating [6,6]-phenyl-C-61-butyric acid methyl ester (PC61BM) and an ethanolamine (ETA)-functionalized fullerene (C-60-ETA) synthesized facilely via a one-pot nucleophilic addition reaction, the average power conversion efficiency (PCE) of the CH3NH3PbI3-based PHJ-PSC devices increased from 13.00% to 16.31%; the best PCE attained was 18.49%, which, to our knowledge, represents the highest PCE reported to date for regular-structure PHJ-PSCs devices based on fullerene-modified TiO2 interlayers. In contrast, single surface engineering of the TiO2 layer with a PC61BM or C-60-ETA layer alone results in only negligible changes in PCE, revealing the synergistic effect of these two fullerene derivatives: the PC61BM layer can passivate the traps on the TiO2 surface, while the subsequent C-60-ETA layer not only improves the wettability of the perovskite film on the ETL but also facilitates electron transport across the interface between the perovskite and the TiO2 ETL. The structural and morphological characterizations show that following dual surface modification of the TiO2 layer with PC61BM and C-60-ETA, both the surface coverage and crystallinity of the CH3NH3PbI3 perovskite film are improved. Steady-state photoluminescence decay and electrochemical impedance spectroscopic studies manifest that the dual surface modification substantially improves the charge extraction efficiency and suppresses charge recombination. As a consequence, this dual surface modification leads to an obvious increase of the short-circuit current density (J(sc)), which contributes primarily to the PCE enhancement. Additionally, because PC61BM may induce passivation of the traps on the TiO2 surface and in the perovskite layer, remarkably, the hysteresis of the current-voltage response is dramatically suppressed following the dual surface modification.

Surface Optimization to Eliminate Hysteresis for Record Efficiency Planar Perovskite Solar Cells

Highly Efficient and Reproducible Planar Perovskite Solar Cells with Mitigated Hysteresis Enabled by Sequential Surface Modification of Electrodes

Pseudohalide-Induced Recrystallization Engineering for CH3NH3PbI3 Film and Its Application in Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells

Eliminated Hysteresis and Stabilized Power Output over 20% in Planar Heterojunction Perovskite Solar Cells by Compositional and Surface Modifications to the Low-Temperature-Processed Tio2 Layer

Improved Planar Perovskite Solar Cells Using the Modified Hole Transporting Layer and Solvent Annealing

Hysteresis-free, stable and efficient perovskite solar cells achieved by vacuum-treated thermal annealing of CH3NH3PbI3

Efficient Perovskite Solar Cells with Reduced Photocurrent Hysteresis Through Tuned Crystallinity of Hybrid Perovskite Thin Films

Successive Surface Engineering Of Tio2 Compact Layers Via Dual Modification Of Fullerene Derivatives Affording Hysteresis-Suppressed High-Performance Perovskite Solar Cells

Rational Design of Solution-Processed Ti-Fe-O Ternary Oxides for Efficient Planar CH3NH3PbI3 Perovskite Solar Cells with Suppressed Hysteresis

Hysteresis-free perovskite solar cells with over 24% efficiency enabled by ZnCl2 doped SnO2 electron transfer layer

Hysteresis-Suppressed High-Efficiency Flexible Perovskite Solar Cells Using Solid-State Ionic-Liquids for Effective Electron Transport

Rationally Induced Interfacial Dipole in Planar Heterojunction Perovskite Solar Cells for Reduced J–V Hysteresis

Employing Lead Thiocyanate Additive to Reduce the Hysteresis and Boost the Fill Factor of Planar Perovskite Solar Cells

A Two-Step Route to Planar Perovskite Cells Exhibiting Reduced Hysteresis

Highly Efficient Perovskite Solar Cells with Neglectable Hysteresis and Increased Open Circuit Voltage Via a Nickel Chloride Interface Modification

Hysteresis‐Free Planar Perovskite Solar Module with 19.1% Efficiency by Interfacial Defects Passivation

Eliminating Light-Soaking Instability in Planar Heterojunction Perovskite Solar Cells by Interfacial Modifications.

Inhibiting hysteresis and optimizing the performance of perovskite solar cells

Enhanced electron extraction using SnO2 for high-efficiency planar-structure HC(NH2)2PbI3-based perovskite solar cells

Modulating J-V hysteresis of planar perovskite solar cells and mini-modules via work function engineering

Enhanced Photovoltaic Performance and Stability of Planar Perovskite Solar Cells by Introducing Dithizone