Abstract:Interfacial engineering is critical for highly efficient charge carrier transport in perovskite solar cells (PSCs). Herein, we developed a new method, called successive surface engineering, that affords PSCs with enhanced efficiency and dramatically suppressed current-voltage hysteresis. Upon modifying the TiO2 compact layer, which is commonly used as an electron transport layer (ETL) in regular-structure (n-i-p) planar heterojunction (PHJ) PSCs, by successively incorporating [6,6]-phenyl-C-61-butyric acid methyl ester (PC61BM) and an ethanolamine (ETA)-functionalized fullerene (C-60-ETA) synthesized facilely via a one-pot nucleophilic addition reaction, the average power conversion efficiency (PCE) of the CH3NH3PbI3-based PHJ-PSC devices increased from 13.00% to 16.31%; the best PCE attained was 18.49%, which, to our knowledge, represents the highest PCE reported to date for regular-structure PHJ-PSCs devices based on fullerene-modified TiO2 interlayers. In contrast, single surface engineering of the TiO2 layer with a PC61BM or C-60-ETA layer alone results in only negligible changes in PCE, revealing the synergistic effect of these two fullerene derivatives: the PC61BM layer can passivate the traps on the TiO2 surface, while the subsequent C-60-ETA layer not only improves the wettability of the perovskite film on the ETL but also facilitates electron transport across the interface between the perovskite and the TiO2 ETL. The structural and morphological characterizations show that following dual surface modification of the TiO2 layer with PC61BM and C-60-ETA, both the surface coverage and crystallinity of the CH3NH3PbI3 perovskite film are improved. Steady-state photoluminescence decay and electrochemical impedance spectroscopic studies manifest that the dual surface modification substantially improves the charge extraction efficiency and suppresses charge recombination. As a consequence, this dual surface modification leads to an obvious increase of the short-circuit current density (J(sc)), which contributes primarily to the PCE enhancement. Additionally, because PC61BM may induce passivation of the traps on the TiO2 surface and in the perovskite layer, remarkably, the hysteresis of the current-voltage response is dramatically suppressed following the dual surface modification.

Eliminated Hysteresis and Stabilized Power Output over 20% in Planar Heterojunction Perovskite Solar Cells by Compositional and Surface Modifications to the Low-Temperature-Processed Tio2 Layer

Highly Efficient and Reproducible Planar Perovskite Solar Cells with Mitigated Hysteresis Enabled by Sequential Surface Modification of Electrodes

Low‐Temperature in Situ Amino Functionalization of TiO2 Nanoparticles Sharpens Electron Management Achieving over 21% Efficient Planar Perovskite Solar Cells

Efficient Planar Perovskite Solar Cells with Low-Temperature Atomic Layer Deposited TiO2 Electron Transport Layer and Interfacial Modifier

Low Temperature Combustion Synthesized Indium Oxide Electron Transport Layer for High Performance and Stable Perovskite Solar Cells

Boosting Efficiency of Planar Heterojunction Perovskite Solar Cells by a Low Temperature TiCl4 Treatment

Low‐Temperature Solution‐Processed ZnO Electron Transport Layer for Highly Efficient and Stable Planar Perovskite Solar Cells with Efficiency over 20%

Eliminating Light-Soaking Instability in Planar Heterojunction Perovskite Solar Cells by Interfacial Modifications.

Laser Derived Electron Transport Layers with Embedded p‐n Heterointerfaces Enabling Planar Perovskite Solar Cells with Efficiency over 25%

Surface Optimization to Eliminate Hysteresis for Record Efficiency Planar Perovskite Solar Cells

Green Low-Temperature-solution-processed in Situ HI Modified TiO2/SnO2 Bilayer for Efficient and Stable Planar Perovskite Solar Cells Build at Ambient Air Conditions

Alleviating Interfacial Recombination of Heterojunction Electron Transport Layer via Oxygen Vacancy Engineering for Efficient Perovskite Solar Cells over 23%

TiO2 Phase Junction Electron Transport Layer Boosts Efficiency of Planar Perovskite Solar Cells

Low-Temperature TiOx Compact Layer for Planar Heterojunction Perovskite Solar Cells.

Ionic liquid modified SnO2 nanocrystals as a robust electron transporting layer for efficient planar perovskite solar cells

Efficient planar heterojunction perovskite solar cells with Li-doped compact TiO2 layer

A low-temperature TiO2/SnO2 electron transport layer for high-performance planar perovskite solar cells

Successive Surface Engineering Of Tio2 Compact Layers Via Dual Modification Of Fullerene Derivatives Affording Hysteresis-Suppressed High-Performance Perovskite Solar Cells

Cesium Iodide Interface Modification for High Efficiency, High Stability and Low Hysteresis Perovskite Solar Cells

Low-temperature Processed Tantalum/niobium Co-Doped TiO2 Electron Transport Layer for High-Performance Planar Perovskite Solar Cells